Karcher BRS 40-1000C EU - Manual (Page 11)

- 3
 Open the cover of the fresh water reser-
voir.
 Pour in water/detergent mixture. Maxi-
mum temperature of the liquid 50°C
 Close the cover of the fresh water res-
ervoir.
 Place the push handle vertically and ar-
rest.
 Insert the transport wheel axles into the
borings on the appliance and lock them.
 Tilt the appliance to the side and drive it
to the place of use on its transport
wheels.
At the site of use:

Press the transport wheel release but-
ton and pull the transport wheel out.
 Insert the transport wheels into their
holder until they stop.
ƽ
Danger
Check the mains cables of the machine
each time before using the machine to see
that it is not damaged. Never operate a
machine with damaged cables. Get the
damaged cables replaced by an electri-
cian.
ṇ Warning
The highest allowed net impedance at the
electrical connection point (refer to techni-
cal data) is not to be exceeded.
 Insert the end of the extension cable as
a loop in the strain relief clamp.
 Plug in the mains plug.
ṇ
Warning
Risk of electric shock. Do not let the mains
cable come in contact with the rotating
brushes or pads.
 Place the slider vertically and arrest.
 Push the push handle down and turn it
to the position indicated above.
 Start up the appliance (see "Cleaning")
and move it forward and backwards
over the surface to be processed.
 Place the slider vertically and arrest.
 Push the push handle down and turn it
to the position indicated above.
 Start the appliance up (see "Cleaing".
 Move the appliance to the left: Press
the left side of the push handle down.
Move the appliance to the right::
Press the rlght side of the push handle
down.
 Slide the lock of the push handle up and
swivel it to a comfortable working
height.
 Turn on the brushes by using the switch
for the brush drive.
 Turn on the brush irrigation by using the
switch for the detergent solution.
 Move the appliance over the surface to
be processed by the push handle (see
"Cleaning method").
ṇ
Caution
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
 Slide the lock of the push handle up and
swivel it to a comfortable working
height.
 Turn on the brushes by using the switch
for the brush drive.
 Move the appliance over the surface to
be processed by the push handle (see
"Cleaning method").
ṇ
Caution
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
Note
To polish underneath furniture, the fresh
water reservoir can be removed.
 Release the switch for detergent solu-
tion.
 Release the brush drive button.
 Place the slider vertically and arrest.
 Disconnect the mains plug.
 Lift up the fresh water reservoir and car-
ry it to the disposal site.
ṇ
Warning
Please observe the local provisions regard-
ing the wastewater treatment.

Remove the cover of the fresh water
reservoir and pour out the liquid via the
notch.
Caution
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.

If you want to transport the appliance on
a vehicle secure it from slipping.
To reduce the required space, the pushing
handle can be folded or disassembled:

Release the star grips of the pushing
handle fastening.
 Unscrew the star grips, remove the
screws and take off the upper push
handle half.
Application Detergent
Routine cleaning of all wa-
ter resistant floors RM 746
RM 780
Routine cleaning of glossy
surfaces (e.g. granite) RM 755 es
Routine cleaning and basic
cleaning of industrial floors RM 69 ASF
Routine cleaning and basic
cleaning of fine stoneware
tiles RM 753
Routine cleaning of tiles in
sanitary areas RM 751
Cleaning and disinfection
in sanitary areas RM 732
Removal of coating from
all alkali-resistant floors
(e.g. PVC) RM 752
Removal of coating from li-
noleum floors RM 754
Driving to the Place of Use
Establish mains contact
Cleaning method
Move the appliance back and forth.
Move the appliance from side to side
Cleaning
Polishing
Shutting Down the Appliance
Emptying the Fresh Water Reser-
voir
Transport
11 EN