A.J. Antunes & Co DFW-150 9100805 - Manual (Page 7)

7 P/N 1010966 Rev. G 08/12
OPERATING INSTRUCTIONS
1. Turn the power on.
2. Allow the unit to preheat for approxi-
mately 30 minutes.
NOTE: The flashing green Ready Light will
become steady when the unit is warmed
up and ready to use.
NOTE: Do NOT push the CYCLE button
during warm-up.
3. Open the top cover and place the
product to be steamed onto the False
Bottom (Figure 5), then close the
cover.
4. Press the appropriate button to initi-
ate a steam cycle
5. Remove steamed product.
WARNING
To avoid injury, be careful when opening top
cover. Be sure to allow steam to escape
before putting hands or face over the
steamer.
READY
UP DOWN PROGRAM
POWER
START/STOP
SINGLE SHOT
Figure 3. Operating Controls
Ready Light
Power
Switch
Cycle
Button
Message
Display
Single Shot
Start/Stop
Button
PROGRAMMING
CYC (Total Cycle Time) refers to the total
programmed steam time set for the product.
SHO (Shot Interval Time) refers to the time set
between shots of steam during a complete cycle.
H2O setting (Steam Shot Time) refers to the
water volume consumed during each water
pump activation.
The amount of steam produced by your Deluxe
Food Warmer depends on the amount of water
sprayed onto the steam generator.
Flooding of the generator may occur if the
H2O setting is too high. To prevent flooding,
the Shot Interval Time (SHO) can be increased
to allow more time for generator heat recov-
ery. Adjustments should be made to both
values to determine the best settings for your
cooking needs.
1. Turn the unit on. The unit displays the
factory programmed Total Cycle Time
in minutes and seconds.
2. Press and release the Program button
to change the control from OPERATION
to PROGRAM mode.
3. To change the Total Cycle Time (CYC)
in minutes, press ▲ or ▼ to change
the time.
4. Press and release the Program button
again, and press ▲ or ▼ to change
the Total Cycle Time in seconds.
5. To change the SHO factory settings,
make sure the control is in PROGRAM
mode, then press and hold both
▲
and ▼ simultaneously for 1-2 seconds
and release. “SHO” will be displayed.
6. Press and release the Program button
and then press ▲ or ▼ to change the
SHO in seconds.
NOTE: Refer to Table 1 for the recommended
settings for your unit.
7. Press and release the Program button
again and press ▲ or ▼ to change the
SHO in minutes.
NOTE: Refer to Table 1 for the recommend-
ed settings for your unit.
8. Press and release the Program button
again and “H2O” will be displayed.
9. To change the H2O (Steam Shot time),
press and release the Program button
again to display the setting. Use
▲ or
▼ to increase or decrease the time.
NOTE: Refer to Table 1 for the recommend-
ed settings for your unit.
10. Press the Start/Stop or Cycle buttons to
store the changes, exit the PROGRAM
Mode, and initiate the cooking cycle.
NOTE: The Single Shot Start/Stop or Cycle
buttons may be pressed at any time dur-
ing programming to store the changes
and exit the PROGRAM Mode.
NOTE: If a change is not made within 5
seconds at any time during the program-
ming process, all changes made up to that
point are stored in memory and the con-
trol reverts to the OPERATION Mode.
RECOMMENDED SETTINGS
Model
Number &
Mfg. No.
CYC SHO H2O
DFW-150
9100109
2 min.,
45 sec. 15 sec.,
0 min.
0_80
DFW-150
9100160
2 min.,
45 sec. 15 sec.,
0 min.
0_80
DFW-250
9100164
2 min.,
45 sec. 15 sec.,
0 min.
0_50
NOTE: If your Mfg. Number is not listed in
Table 1, there are no recommended set-
tings for that unit.
Table 1. Recommended Settings