Samsung PS50A476P1D - Manual (Page 47)

English - 4
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER
button.
Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
4 Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
5 Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound through the 2-channel
receiver.
➢
If the receiver is exclusively for a home theater only (supporting audio only), it may
not appear in the device list.
➢
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.
➢
In case of a content with copyright problems, listening through the receiver may not properly operate.
Check Points before Requesting Service
Symptom Solution
Anynet+ does not work. ■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure
to search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. ■ Check if the Anynet+ device is properly connected to the TV and
check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+
Setup menu.
■ Press the TV button on the TV remote control to switch to TV.
Then press the TOOLS button to show the Anynet+ menu and
select a menu you want.
I want to exit Anynet+. ■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of P, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
The message Connecting to
Anynet+ device… appears
on the screen.
■ You cannot use the remote control when you are configuring
Anynet+ or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to
view mode is complete.
The Anynet+ device does
not play.
■ You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI cable only.
Some HDMI cables may not support Anynet+ functions.
The TV programme cannot
be recorded.
■ Check whether the antenna jack on the recording device is
properly connected.
The TV sound is not output
through the receiver.
■ Connect the optical cable between TV and the receiver.
Enter Move
View TV
Select Device 
Record 
Menu on Device 
Device Operation 
Receiver :On 
Setup 
TV P 1
Exit
BN68-01422A.indb 47 2008-04-18 오전 11:03:21