Samsung UN60C6300SFXZA - Manual (Page 2)

Step 5 : Remote Control
Remote Control Buttons and Functions
✎ This is a special remote control for the visually impaired and has Braille points on the Power, Channel and Volume buttons.
Selecting a Source
To watch a movie on your Blu-ray player or watch
your favorite TV show, you must select the correct
source. A source is a device, such as a Blu-ray/DVD
player, a cable/satellite box, antenna or a cable TV
input. Sources can be connected to your TV through
the HDMI, DVI, Component, Composite, or D-sub
connections, or through the Antenna or Cable In connections.
To view the signal from a source connected to the HDMI, DVI, Component,
Composite, or D-sub jack, press the
SOURCE button on your remote. Each time
you press the SOURCE button, you change to a different source.
Viewing the On Screen Menus
To view the On Screen Menus, follow these steps:
1. With the power on, press the
MENU button on
your remote. The main menu appears.
The menu’s left side has the following menu
options: Picture, Sound, Channel, Setup,
Input, Application and Support.
2. Press the ▲ or ▼ button on your remote to select a menu option, and then
press the ENTER E button.
3. When done using the menu, press the EXIT button on your remote to exit.
Step 6 : The Media Play Features
The Media Play feature lets you connect to your PC through your home network and
stream PC audio and video files to your HDTV using your remote. To use IPTV or
Samsung PC Share Manager, you must connect your TV to your network. You can
attach the TV to your network in two ways, by cable, using CAT 5 cable, or wirelessly,
using a Samsung Wireless LAN Adapter. Instructions for both connection methods are
below.
Network Connection - Wired
There are two main ways to connect your TV to your network using cable,
depending on your network setup. They are illustrated below:
Configuring the Network Connection - Wired
Most home networks use the Dynamic Host Configuration Protocol (DHCP) to
configure network connections. Home networks that support DHCP automatically
provide the IP address, subnet mask, gateway, and DNS values your TV needs to
access the Internet so you don’t have to enter them manually.
To configure your network connection for a network that uses DHCP, follow these
steps:
1. Connect your TV to your network as shown in one of the illustrations above.
2. Turn on your TV, press the
MENU button on your remote, and then select
Setup → Network.
3. Set the Network Type to Wired if it is not already set to Wired.
4. Select Network Setup. The
Network Setup screen appears.
5. On the Network Setup menu,
set Internet Protocol Setup and
DNS to Auto. Auto acquires and
enters the necessary internet values
automatically.
6. Select Network Test to check
Internet connectivity.
✎ Some networks are Static
IP networks. If your network
is a Static IP network, you can not use DHCP to configure the network
connection. Instead, you must enter the IP Address, Subnet Mask,
Gateway, and DNS Server manually. For instructions explaining how to
configure a Static IP network, see your user’s manual.
CH LIST
MUTE
POWER
SOURCE
PRE-CH
ON/OFF
MENU
TOOLS
RETURN
S.MODE
P.MODE
MEDIA.P FAV.CH
P.SIZE CC
SLEEP
A B C D
MTS
EXIT
INFO
Changing Channels and Adjusting the Volume
Adjust the volume by pressing the Volume button
on the remote.
CH LIST
MUTE
POWER
SOURCE
PRE-CH
ON/OFF
MENU
TOOLS
RETURN
S.MODE
P.MODE
MEDIA.P FAV.CH
P.SIZE CC
SLEEP
A B C D
MTS
EXIT
INFO
Change the channels by pressing the Channel button on the remote.
✎ If your TV is attached to a cable or satellite box, change the channel using
the box’s remote.
✎ You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button.
Network Connection - Wireless
You can connect your TV to your LAN through a standard wireless router or
modem. To connect wirelessly, you must first attach a “Samsung Wireless LAN
Adapter” (WIS09ABGN, WIS09ABGN2, WIS10ABGN - sold separately) to either the
USB 1 (HDD) or USB 2 port on the back of your TV. See the illustration below.
Samsung’s Wireless LAN adapter is sold separately and is offered by select
retailers, Ecommerce sites and Samsungparts.com. Samsung’s Wireless LAN
adapter supports the IEEE 802.11A/B/G and N communication protocols.
Samsung recommends using IEEE 802.11N. When you play the video over a IEEE
802.11B/G connection, the video may not play smoothly.
Most wireless network systems incorporate a security system that requires devices
that access the network through an access point or AP (typically a wireless IP
Sharer) to transmit an encrypted security code called an access key.
If Pure High-throughput (Greenfield) 802.11N mode is selected and the Encryption
type is set to WEP, TKIP or TKIPAES (WPS2Mixed) for your AP, Samsung TVs will
not support a connection in compliance with new Wi-Fi certification specifications.
Configuring the Network Connection - Wireless
The instructions below are for networks that use the Dynamic Host Configuration
Protocol (DHCP) to configure network connections automatically. If your have a
Static IP network, see your user’s manual for configuration instructions.
To configure your network connection for a network that uses DHCP, follow these
steps:
1. Connect your TV to your network as shown in the illustrations above.
2. Turn on your TV, press the
MENU button on your remote, and the select Setup
→ Network.
3. Set the Network Type to Wireless if it is not already set to Wireless.
4. Select Network Setup. The
Network Setup screen appears.
5. On the Network Setup menu,
select an AP(Access Point) and ad
hoc network. if you have selected
network with a security key, the
Security Key screen appears.
6. Enter the security key using the
numbers on the remote, and then
press the Blue button on your
remote.
✎ If your network uses WEP security encryption, 0~9 and A~F will be
available on the Security Key screen. Use the Direction button on your
remote to move to the characters and the enter key to select them.
7. On the Network Setup menu, set Internet Protocol Setup and DNS to Auto.
The Auto acquires and enters the necessary internet values automatically.
8. Select Network Test to check internet connectivity.
✎ For more information, see your user’s manual.
Connecting a USB Device for Media Play
You can enjoy photo, music,
and movie files stored on a
USB device by connecting
it to the TV and using
the Media Play feature.
For Media Play operating
instructions, please see your
Owner’s Manual.
The LAN Port on the Wall
LAN Cable (Not Supplied)
TV Rear Panel
Modem Cable (Not Supplied) LAN Cable (Not Supplied)
The Modem Port on the Wall TV Rear Panel External Modem
(ADSL / VDSL / Cable TV)
The LAN Port on the Wall
LAN Cable (Not Supplied)
Wireless IP sharer
Samsung Wireless LAN
Adapter
or
TV Rear Panel
SUM Change Device View Devices E Enter R Return
MediaPlay
Videos
:
:
:
:
:
:
U Move E Enter R Return
Internet Protocol Setup Auto r
IP Address
Subnet Mask
Gateway
DNS Auto
DNS Server
Network Setup
:
:
:
:
:
:
:
PBC(WPS) U Move E Enter R Return
Select a network Not Selected r
Internet Protocol Setup Auto
IP Address
Subnet Mask
Gateway
DNS Auto
DNS Server
Network Setup
BN68-02957A-01
CH LIST
MUTE
POWER
SOURCE
PRE-CH
ON/OFF
MENU
TOOLS
RETURN
S.MODE
P.MODE
MEDIA.P FAV.CH
P.SIZE CC
SLEEP
A B C D
MTS
EXIT
INFO
Turns the TV on and off.
Returns to the previous channel.
Cuts off the sound temporarily.
Changes channels.
Turns the remote control light on or off. When on, the
buttons become illuminated for a moment when pressed.
(Using the remote control with this button set to ON will
reduce the battery usage time.)
Displays Favorite Channel Lists on the screen.
Displays the channel list on the screen.
Displays information on the TV screen.
Selects the on-screen menu items and changes the values
seen on the menu.
Exits the menu.
S.MODE : Press to select the sound mode.
SLEEP : Use to set the sleep timer function.
MTS : Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
P.MODE : Press to select the picture mode.
P.SIZE : Selects the picture size.
CC : Controls the caption decoder.
Displays and selects the available video sources.
Press to directly access channels.
Press to select additional channels (digital) being
broadcasted by the same station. For example, to select
channel “54-3”, press “54”, then press “–” and “3”.
Adjusts the volume.
Brings up the OSD.
Displays Media Play.
Quickly select frequently used functions.
Returns to the previous menu.
These buttons are for the Channel list, Media Play
menu, etc.
Use these buttons in Media Play and
Anynet+ (HDMI-CEC) modes.
(�: Controls recording for Samsung recorders that
have the Anynet+ feature)
CH LIST
MUTE
POWER
SOURCE
PRE-CH
ON/OFF
MENU
TOOLS
RETURN
S.MODE
P.MODE
MEDIA.P FAV.CH
P.SIZE CC
SLEEP
A B C D
MTS
EXIT
INFO
[QSG-6300]BN68-02957A-01Eng.indd 2 2010-09-03 오후 6:16:43