Samsung HLT7288WX-XAA - Manual (Page 84)

English - 84
Listening through a Home theater
You can listen to sound through a receiver (home theater) instead of the TV’s speakers.
1 Press the Anynet+ button.
2 Press the ▲ or ▼ button to select Receiver, press the ◄ or ► button to select to On. Now
you can listen to sound through the Home theater receiver.
Press the EXIT button to exit.
➢ When the receiver (home theater) is set to On, you can hear sound output from the TV’s
Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel
sound to the Home theater receiver. When the source is a digital component such as a DVD
and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home
Theater receiver.
➢ If your Home Theater receiver supports audio only, it may not appear in the device list.
➢ The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV.
➢ When the Home Theater is set to On, a Bluetooth device connected to the TV may not work properly. Operating a connected
Bluetooth device may also make it impossible to hear audio from the Home Theater Receiver.
➢ When using the WISELINK feature, sound may not output properly through the receiver.
➢ When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS, Preferred language) menus.
Troubleshooting for Anynet+
Symptom Solution
Anynet+ does not work. ■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices
only.
■ Connect only one receiver (home theater).
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels, operating WISELINK)
■ When connecting or removing the HDMI cable, please make sure to search devices
again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. ■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the Anynet+
button to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+. ■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet+ devices.
■ Press any of CH, CH LIST, PRE-CH, and FAV.CH to change to the TV mode. (Note that
the channel button operates only when an Anynet+ device with a built-in tuner is not
connected.)
The Connecting to Anynet+ device
…message appears on the screen.
■ You cannot use the remote control when you are configuring Anynet+ or switching to a
view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does not play. ■ You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether is set to in the Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may
not support Anynet+ functions.
The TV program cannot be
recorded.
■ Check whether the antenna jack on the recording device is properly connected.
The TV sound is not output through
the receiver.
■ Connect the optical cable between TV and the receiver.
Device List
Record
Timer Recording
Receiver Off
Headset Connection
Picture Setting
Sound Setting
Sleep Timer Off
▼
Move Enter
BP68-00640A-00Eng.indb 84 2007-04-23 ¿АИД 4:18:07