Т³гж 6, Nomenclature and functions, Projectmix10 – t&mSystems Project MIX10 User Manual
Page 6
6
4. NOMENCLATURE AND FUNCTIONS
2
4.1 FRONT PANEL
1
4
5
6
7
1. CHIME
Pressing chime switch, chime signal
will be activated as a pre signal. You
can adjust level.
=
OUTPUT SWITCH
This is for selector that send chime
signal to master output.Chime signal
has a priority .when chime signal is
activated, signal output of input 5~10
will be closed.
IMPORTANT NOTICE:Priority will be
given only for selected output.
2. INPUT1 CONTROLS
Adjust level volume so as not to turn
on +3CLIP LED under two~three o
clock of master volume this is control
For mic input level.
=
OUTPUT SWITCH
This is selector that send signal of
input 1 to the master output.when
input 1 are activated , signal of input
5~10 will be closed.
3. INPUT 2,3,4 CONTROLS
Adjust level volume so as not to
turn on +3LED under two~three o
clock of master volume this is
control for MIC/LINE input closed.
=
OUTPUT SWITCH
This is selector that send signal of
input 2,3,4 to the master output.
when input 2~4 are activated , signal
of input 5~10 will be closed.
=
MODE SWITCH
MIC : It is input mic switch of 300Hz
H.P.F that makes sound
clearance.when you select
Switch , windy sound.
MIC : This is MIC input switch
Without filter line.
LINE : Line input for CD CASSETTE,
TUNER.
IMPORTANT NOTICE:Serecting
mode switch
HPF
flat
power will be supplied to
input XLR connector for condensor
mic only.If you connect unbalanced
dynamic microphone with them,it
May be defaulted and should be
moving to mode switch for noise
Down.
=
PRIORITY 2~4
When you switch
on
, priority is
activated and will closed input 5~10.
4. INPUT 5~10 CONTROLS
These make adjustment of MIC/LINE
For input 5~10.
Adjust output level so as not to tune
on
CLIP LED under two o
clock.
=
OUTPUT SWITCH
This is selector that send signal of
input 5~10 to the master-output.
When input 1~4 signal and chime
signal are supplied, priority will be
activated and close output of input
5~10.
This is selector that send signal of
input 2,3,4 to the master output
when input 2~4 are activated , signal
of input 5~10 will be close.
=
MODE SWITCH
MIC : It is input mic switch of 300Hz
H.P.F that makes sound
clearance.when you select
Switch , windy sound.
MIC : This is MIC input switch
Without filter line.
LINE : Line input for CD CASSETTE,
TUNER.
IMPORTANT NOTICE:Serecting
mode switch
HPF
flat
power will be supplied to
input XLR connector for condensor
mic only.If you connect unbalanced
dynamic microphone with them,it
May be defaulted and should be
Minimized level volume before
moving to mode switch for noise
Down.
5. EQUALIZER
Adjust low, high if EQ volume
According to condition.
6. MAST 1,2
This is master volume for all input
levels you and better use toward two
o
clock adjust level before clipping
for proper operation.
7. POWER SWITCH
Press to turn ON the power.
Press again to turn the power OFF.
3
ProjectMix10
P
r
o
j
e
c
t
M
ix
1
0
PROJECT
Mix10
CH 4
CH 5
CH 6
CH 7
CH 8
CH 9
CH 10
CHIME
POWER
CH 2
-PAGEMIC 1
CH 3
MASTER 1
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
1 1+2 2
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
PRIORITY2
PRIORITY3
PRIORITY4
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
+3
0
-3
-8
-13
LOW
HIGH
HIGH
MASTER 2
VOLUME
LOW
0
0
0
0