Siemens LC98KA570 - Manual (Page 14)

14
Saturation display
When the metal mesh grease filters or activated carbon filter
are saturated, the corresponding symbol flashes:
■
Metal mesh grease filter: !?
■
Activated carbon filter: "?
When this happens, do not delay cleaning the metal mesh
grease filters or replacing the activated carbon filter any longer.
For instructions on how to clean the metal mesh grease filters,
please refer to the section Cleaning and maintenance.
While the saturation displays are flashing, they can be reset. To
do this, press the – button.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be
switched over accordingly:
■
The extractor hood must be connected and switched off.
■ Press and hold the # and x buttons at the same time until
the " display lights up.
■ Repeatedly press the button combination to switch the
electronic control display back to exhaust air mode ( !
display).
Cleaning and maintenance
:
Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
:
Risk of electric shock!
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
:
Risk of electric shock!
Penetrating moisture may cause an electric shock. Do not use
any high-pressure cleaners or steam cleaners.
:
Risk of injury!
Components inside the appliance may have sharp edges. Wear
protective gloves.
Cleaning agents
Observe the information in the table to ensure that the different
surfaces are not damaged by using the wrong type of cleaning
agent. Do not use
■ harsh or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■ hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the cleaning
agents.
Cleaning the metal mesh grease filters
:
Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
■
Do not use any aggressive, acidic or alkaline cleaning
agents.
■
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
■
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
■
Do not clean heavily soiled metal mesh grease filters together
with utensils.
■
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
By hand:
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
■
Soak the metal mesh grease filters in a hot soapy solution.
■ Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
Area Cleaning agents
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth.
Clean stainless steel surfaces in the
direction of the grain only.
Special stainless steel cleaning prod-
ucts are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Painted surfaces Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth/towel.
Do not use any stainless steel clean-
ers.
Aluminium and
plastic
Glass cleaner:
Clean with a soft cloth.
Glass Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Operating controls Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth.
Risk of damage to the electronics
from penetrating moisture. Never
clean operator controls with a wet
cloth.
Do not use any stainless steel clean-
ers.
Area Cleaning agents