State SBD100 399NE A - Manual (Page 23)

23
MECHANICAL VENTING
SINGLE UNIT INSTALLATION
When mechanical venting of these heaters is desired, the
following kits are available.
SBD 120 through the SBD 200/A
State part number 193933
SBD 250/A through the SBD 500/A
State part number 193933-1
Where an approved power venter is to be installed to operate in
conjunction with the water heater thermostat, the following codes
must be adhered to. Field wiring should conform to the latest
version of the National Electric Code ANSI/NFPA No. 70. For
Canadian installations the electrical connections and grounding
shall be done in accordance with the current Canadian Electrical
Code CSA C22.1 Part 1 and/or local codes.
NOTE: The power venter must be installed downstream of the
drafthood. See figure 13.
FIGURE 13
VENT INSTALLATION
Seal all joints between the power venter and the vent termination.
This is to prevent leakage of exhaust products into the room(s)
due to positive pressure of blower.
The "Sequence of Operation" description will be the same with
mechanical venting except,
When the appliance thermostat calls for heat:
Thermostat contacts "Close" and the power venter blower
(120 VAC) is energized. Sufficient draft must be established for
the "Draft Prover Switch (N.O.)" to "Close". When the draft prover
switch "Closes" the relay coil of the flue damper is energized.
See side wall vent kit installation manual for complete
instructions.
MULTIPLE UNIT INSTALLATIONS
For multiple unit installations, contact State Water Heaters
Technical Support Center at 1-800-527-1953.
TABLE 5
MANIFOLD GAS PRESSURE IN INCHES
OF WATER COLUMN (ALL MODELS*)
TYPE OF GAS
NATURAL PROPANE
3.5 10.0
Gas pressure specified in Table 5, refer to flow pressure taken
at pressure tap of automatic gas valve while heater is operating.
TABLE 6
APPROXIMATE TIME REQUIRED TO CONSUME
1 CU. FT. OF GAS AT FULL CAPACITY
TIME REQ’D
INPUT TYPE BTUH TO CONSUME
RATE OF PER 1 CU. FT.
(BTUH) GAS CU. FT. OF GAS
120,000 NATURAL 1050 31.5 SEC.
PROPANE 2500 75.0 SEC.
154,000 NATURAL 1050 24.5 SEC.
PROPANE 2500 58.4 SEC.
180,000 NATURAL 1050 21.1 SEC.
PROPANE 2500 50.3 SEC.
190,000 NATURAL 1050 19.9 SEC.
PROPANE 2500 47.4 SEC.
199,000 NATURAL 1050 19.0 SEC.
PROPANE 2500 47.4 SEC.
250,000 NATURAL 1050 15.1 SEC.
PROPANE 2500 35.3 SEC.
251,000 NATURAL 1050 15.06 SEC.
PROPANE 2500 35.1 SEC.
275,000 NATURAL 1050 13.75 SEC.
PROPANE 2500 32.2 SEC.
305,000 NATURAL 1050 12.4 SEC.
PROPANE 2500 29.5 SEC.
360,000 NATURAL 1050 11.4 SEC.
PROPANE 2500 24.0 SEC.
365,000 NATURAL 1050 10.4 SEC.
PROPANE 2500 24.7 SEC.
399,000 NATURAL 1050 9.5 SEC.
PROPANE 2500 22.6 SEC.
500,000 NATURAL 1050 7.6 SEC.
PROPANE 2500 18.0 SEC.
Figures shown are valid for 0-2000 ft.(0-610m) installations.
See “HIGH ALTITUDE INSTALLATIONS” for deration
requirements over 2000 ft.(610m).
TABLE 7
PILOT BURNER INFORMATION
PILOT BURNER RATED
TYPE OF PART NUMBER ORIFICE
MODEL GAS (WITH ORIFICE) SIZE
ALL NATURAL 193314-0 0.018
MODELS PROPANE 193314-1 0.014