GE GTDL210GDWW - Manual (Page 8)

ADDING ELBOW FOR EXHAUST
THROUGH BOTTOM OF CABINET
• Insert the elbow through the rear opening and connect
it to the dryer internal duct.
• Apply duct tape on the joint between the dryer internal
duct and elbow, as shown above.
ADDING COVER PLATE TO REAR OF
CABINET
Connect standard metal elbows and ducts to complete
the exhaust system. Cover back opening with a plate
.LW:(0DYDLODEOHIURP\RXUORFDOVHUYLFHSURYLGHU
3ODFHGU\HULQ¿QDOORFDWLRQ
CAUTION:
Internal duct joints must be secured with tape,
otherwise they may separate and cause a
safety hazard.
WARNING-
NEVER LEAVE THE
BACK OPENING WITHOUT THE PLATE
.,7:(0
5(*,67(5<2851(:$33/,$1&(725(&(,9(
$1<,03257$17352'8&7127,),&$7,216
Please go to www.GEAppliances.com or mail in
your product registration card.
)RUTXHVWLRQVRQLQVWDOODWLRQFDOO86RU
&DQDGD
SERVICING
WARNING-
LABEL ALL WIRES PRIOR
TO DISCONNECTING WHEN SERVICING
&21752/6:,5,1*(55256&$1&$86(
IMPROPER AND DANGEROUS OPERATION
$)7(56(59,&,1*,167$//$7,21
PL ATE
(KIT WE1M454)
Installation Instructions
CHANGING DIRECTION OF DOOR OPENING
2SHQWKHGRRUDQGUHPRYHWKH¿OOHUSOXJVRSSRVLWHWKH
hinges. With the door completely open, remove the
bottom screw from each hinge on the dryer face. Insert
these screws about half way into the TOP holes, for each
KLQJHRQWKHRSSRVLWHVLGHZKHUH\RXUHPRYHGWKH¿OOHU
SOXJV$SSO\¿UPSUHVVXUHWRJHWWKHVFUHZVVWDUWHG
2. Loosen the top screw from each hinge on the dryer face
half way. With one hand holding the top of the door and
the other hand holding the bottom, remove the door
from the dryer by lifting it UP and OFF.
REMOVE BOTTOM SCREW FROM EACH HINGE
$1',167$//+$/):$<,172($&+TOP OF
OPPOSITE HINGE HOLES
REMOVE 4 PLUGS AND KEEP
FOR INSERTION INTO
THE OPPOSITE SIDE
3. Remove the blind plate from
the hinge side of the dryer
by removing its two screws.
Remove the strike plate from
the opposite side of the dryer
by removing its two screws.
Reinstall the plates, on the
opposite sides, using two
screws in each plate.
4. 5RWDWH WKH GRRU ž ,QVHUW WKH GRRU RQ WKH RSSRVLWH
side of the opening by moving the door ON and DOWN
until the top hinge and the bottom hinge are resting on
WKHWRSVFUHZVLQVHUWHGLQVWHS
5. Remove the remaining screws from the side of the
opening from which the door was removed. With these
screws secure each hinge at the bottom. Tighten the
two top screws on each hinge. Reinsert the plastic plugs
on the side from which the door was removed.
LOOSEN EACH TOP HINGE
6&5(:+$/):$<$1'/,)7
THE DOOR UP AND OFF
527$7('225ž$1'+$1*
IT ON TOP HINGE SCREWS
,167$//$1'7,*+7(1%27720
SCREWS AND TIGHTEN TOP
SCREWS
INSERT PLUGS
INTO HOLES ON
OPPOSITE SIDE
FRONT PANEL
SWITCH
STRIKE
PLATE
BLIND
PLATE