GE GTDX185EDCC - Manual (Page 7)

Installation Instructions
7
• Apply duct tape as shown on the joint between the
dryer internal duct and the elbow.
ADDING ELBOW FOR EXHAUST
THROUGH BOTTOM OF CABINET
• Insert the elbow through the rear opening and connect
it to the dryer internal duct.
• Apply duct tape on the joint between the dryer internal
duct and elbow, as shown on page 6.
ADDING COVER PLATE TO REAR
OF CABINET (SIDES AND BOTTOM
EXHAUST)
Connect standard metal elbows and ducts to complete
the exhaust system. Cover back opening with a plate
(Kit WE1M454) available from your local service provider.
3ODFHGU\HULQ¿QDOORFDWLRQ
WARNING-
NEVER LEAVE THE BACK
OPENING WITHOUT THE PLATE. (Kit
WE1M454)
PL ATE
(KIT WE1M454)
DUCT
TAPE
CAUTION:
Internal duct joints must be secured with tape,
otherwise they may separate and cause a
safety hazard.
CAUTION:
Internal duct joints must be
secured with tape, otherwise
they may separate and cause
a safety hazard.
CHANGING DIRECTION OF DOOR OPENING
1. 2SHQWKHGRRUDQGUHPRYHWKH¿OOHUSOXJVRSSRVLWHWKH
hinges. With the door completely open, remove the
bottom screw from each hinge on the dryer face. Insert
these screws about half way into the TOP holes, for each
KLQJHRQWKHRSSRVLWHVLGHZKHUH\RXUHPRYHGWKH¿OOHU
SOXJV$SSO\¿UPSUHVVXUHWRJHWWKHVFUHZVVWDUWHG
2. Loosen the top screw from each hinge on the dryer face
half way. With one hand holding the top of the door and
the other hand holding the bottom, remove the door
from the dryer by lifting it UP and OFF.
5HPRYHWKHEOLQGSODWHIURP
the hinge side of the dryer
by removing its two screws.
5HPRYH WKH VWULNH SODWH
from the opposite side of the
dryer by removing its two
VFUHZV5HLQVWDOOWKHSODWHV
on the opposite sides, using
two screws in each plate.
4. 5RWDWH WKH GRRU ž ,QVHUW WKH GRRU RQ WKH RSSRVLWH
side of the opening by moving the door ON and DOWN
until the top hinge and the bottom hinge are resting on
the top screws inserted in step 1.
5. 5HPRYH WKH UHPDLQLQJ VFUHZV IURP WKH VLGH RI WKH
opening from which the door was removed. With these
screws secure each hinge at the bottom. Tighten the
WZRWRSVFUHZVRQHDFKKLQJH5HLQVHUWWKHSODVWLFSOXJV
on the side from which the door was removed.
LOOSEN EACH TOP HINGE
6&5(:+$/):$<$1'/,)7
7+('22583$1'2))
11
527$7('225ž$1'+$1*
,721723+,1*(6&5(:6
INSTALL AND TIGHTEN BOTTOM
6&5(:6$1'7,*+7(1723
6&5(:6
,16(573/8*6
INTO HOLES ON
OPPOSITE SIDE
FRONT PANEL
SWITCH
STRIKE
PLATE
BLIND
PLATE
5(029( BOTTOM6&5(:)520($&++,1*(
AND INSTALL HALF WAY INTO EACH TOP OF
OPPOSITE HINGE HOLES
5(029(3/8*6$1'.((3
)25,16(57,21,172
THE OPPOSITE SIDE