Asus Motherboard NCLV-D (A) - Manual (Page 48)

2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
4 . 4 . 4 . 4 . 4 . S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) (Optional)
These connectors are for Serial ATA signal cables. These connectors
support up to four Serial ATA hard disk drives that you can configure
as a disk array through the onboard SATA RAID controller. Refer to
Chapter 3 for details on how to set up Serial ATA RAID configurations.
Before creating a RAID set using Serial ATA hard disks, make sure that
you have connected the Serial ATA signal cable and installed Serial ATA
hard disk drives; ; otherwise, you cannot enter the RAID utility and SATA
BIOS setup during POST.
5 . 5 . 5 . 5 . 5 . H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 )
This connector supplies power to the hard disk activity LED. The read
or write activities of any device connected to the primary/secondary
IDE connectors or the SATA connectors cause this LED to light up.
NCLV-D
NCLV-D SATA RAID connectors
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA_RAID1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA_RAID2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA_RAID3
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA_RAID4
NCLV-D
NCLV-D
SCSI/SATA card activity LED connector
HDLED1
1
SCSI_ACTLED-
SCSI_ACTLED+
SCSI_ACTLED-
SCSI_ACTLED+