American Standard 1660.200 - Manual (Page 2)

5 0 3 2 1 B
Turn off hot and cold water supplies before beginning.
CAUTION
INSTALL TRIM
1
3
TEST DIVERTER
2
See Roughing-in Drawing on reverse side. The port with the BATH TUB picture is the high flow.
The DIVERTER can be installed with the inlet rotated in any position.
Supply connections are 1/2" NPT connections.
For proper positioning the finished wall must be within side of PLASTER GUARD.
Connect water to valve. The reverse side of the body is marked with arrows.
CAUTION: Do not solder near the VALVE. Damage to the SEAL may occur.
Do not seal any outlets. The DIVERTER cannot be used as a stop valve.
For support use pipe braces secured to wooden braces.
For 1660.431/.441 Series:
Assemble HANDLE SKIRT then HANDLE LEVER to ESCUTCHEON NUT STEM. Secure
with HANDLE SCREW.
Remove INDEX BUTTON (or unscrew VANDAL RESISTANT INDEX CAP).
Check that the DIVERTER operates correctly and does not leak.
To do this, screw off the PLASTER GUARD, turn around, and
insert using the fluted pin into the fluting on the DIVERTER SPINDLE
and use as a diverter knob. Screw the PLASTER GUARD back on.
Have the wall tiled only with the PLASTER GUARD screwed on.
ROUGHING-IN
SERVICE
4
Unscrew ESCUTCHEON HOLDER and
remove HOLDER and ESCUTCHEON.
To Replace O-Rings:
ESCUTCHEON
CAP
HANDLE
HANDLE
ADAPTER
HANDLE
SCREW
ESCUTCHEON
NUT STEM
DECORATOR
RING
DIVERTER
DIVERTER
SPINDLE
PLASTER
GUARD
MAX
DISK
O-RING
DISK
O-RING
LOWER
DISK
UPPER
DISK
SHAFT
SPRING
CAP
WASHER
WASHER
SHAFT
O-RING
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 1 9 9 5
INDEX
BUTTON
HANDLE
SKIRT
VANDAL-RESISTANT
INDEX CAP
VANDAL-RESISTANT
HANDLE SCREW
HANDLE
SCREW
To operate, turn the HANDLE clockwise or counter clockwise.
Check for leaks.
To operate, turn the HANDLE clockwise or counter clockwise.
Check for leaks.
Snap on HANDLE CAP.
Assemble HANDLE and DECORATOR RING onto
HANDLE ADAPTER. Secure with HANDLE SCREW.
Push HANDLE ADAPTER onto STEM.
Make sure arrow is up.
Place ESCUTCHEON on ESCUTCHEON
HOLDER and screw HOLDER onto VALVE.
When finished tiling wall, remove
PLASTER GUARD.
For 1660.430/.440 Series:
For 1660.430/.440 Series:
Push on INDEX BUTTON or screw on VANDAL RESISTANT INDEX CAP.
Replace remaining parts in reverse order.
Remove old DIVERTER elements and
install new parts.
Unscrew CAP and remove STEM,
SPRING and SEALS.
Unscrew ESCUTCHEON HOLDER and remove HOLDER
and ESCUTCHEON.
Replace remaining parts in reverse order.
Remove old DIVERTER elements and install new parts.
Unscrew CAP and remove STEM, SPRING and SEALS.
Remove HANDLE SCREW, DECORATOR
RING, HANDLE and ADAPTER.
Use a small screw driver to
remove HANDLE CAP.
Turn off water supply.
For 1660.431/.441 Series:
Remove HANDLE SCREW, LEVER HANDLE and HANDLE SKIRT.
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
IN CANADA 1-800-387-0369 (TORONTO 1-416-536-5609)
(For 1660.200/.300, handles are
purchased separately.)