Blue-White F-451 Polysulfone Molded - Manual

® Your Blue-White F-451 Series
® !Your Blue-White flowmeter was designed to be easy to
install.
!Please read the Instruction Guideline on the next page
before installing your flowmeter.
!This flowmeter is an instrument, special care should be
taken when handling and installing.
Inspection of the Flowmeter and Compatibility
Installation Instructions
80000-247 09/18/2012
F-451
Blue-White
Industries, Ltd.
R
Materials of Construction
Meter Body: Polysulfone
Shield (optional): Polycarbonate
Float: 316SS, Hastelloy C-276, or PTFE
(based on model)
Guide rod: # 316 Stainless (opt. Hastelloy C-276)
Adapters: Polysulfone or PVC (optional Brass)
Wireholder: Polysulfone
Float Stop: TFE/P (Aflas)
Union Nuts: Nylon
O-Rings: Viton
Scale: Permanent, dual scale silkscreen (black ink)
Accuracy: ± 3% of full scale reading
BLUE-WHITE INDUSTRIES LIMITED WARRANTY
FLOWMETERS are warranted to be free of defects in material and workmanship
for up to 12 months from the date of factory shipment. Warranty coverage is
limited to repair or replacement of the defective flowmeter only. Blue-White
Industries does not assume responsibility for any other damage that may occur.
This warranty does not cover damage to the flowmeter that results from misuse
or alterations, nor damage that occurs as a result of: meter misalignment,
improper installation, over tightening, use of non- recommended chemicals, use
of non-reccomended adhesives or pipe dopes, excessive heat or pressure, or
allowing the meter to support the weight of related piping. Flowmeters are tested
and calibrated with water and air only. Although meters may be suitable for other
chemicals, Blue-White cannot guarantee their suitability.
Flowmeters are repaired at the factory only. Call or write the factory to receive a
Return Authorization Number, carefully pack the flowmeter to be returned,
including a brief description of the problem. Note the RA number on the outside
of the carton.
Website: www.Blue-White.com
E-mail: [email protected] | [email protected]
Phone: 714-893-8529 | Fax: 714-894-9492
5300 Business Drive
Huntington Beach, CA 92649
Blue-White
Industries, Ltd.
R
BLUE-WHITE
14-1/2 in.
(368 mm)
3-3/16 in.
(81 mm)
1
.5 - 6 GPM / 2 - 20 LPM Polysulfone
1 - 10 GPM / 4 - 40 LPM
Polysulfone
2 - 20 GPM / 7.5 - 75 LPM
7
F-45023N-4
F-45023N
F-45023N-1
F-45023N-2
1
Float, .5 - 6 GPM PTFE
Float, 1 - 10 GPM, Stainless Steel
Float, 1 - 10 GPM, PTFE
Float, 2 - 20 GPM, 8 - 80 SCFM,
Stainless Steel
Float, 2 - 20 GPM, Hastelloy
6
F-45032T
F-45033
F-45054T
F-45034
F-45035H
F-45037
F-451 Exploded View and Parts List
Catalog Description Amount Item
8
F-45028
F-45028H
F-450028-2 Guide Wire, .5-6, 1-10, 2-20,8-80
SS
Guide Wire, .5-6, 1-10, 2-20, 8-80
1
4 F-45025 Wireholder, Top 1
9 F-45046 Wireholder, .5-6, 1-10, 2-20, 8-80 1
5 2-006A Float Stop, .5-6, 1-10, 2-20, 8-80 1
3 2-136V O-Ring 2-136 Viton 2
2
Adapter, vertical, 1” F/NPT PSF
Adapter, vertical, 1” F/NPT Brass
Adapter, vertical, 1” sweat Brass
Adapter, vertical, 1-1/2” M/NPT
2
F-45030N
F-45047N
F-45039N
F-45036
1 F-45038N Union Nut 2
Not F-45034 Adapter, for shield, PVC 2
Not F-45034S Shield, clear polycarbonate 1
! Check for damage while unpacking the flowmeter.
! Remove any instruction sheets and shipping materials that may have
been inserted into the meter body for shipping reasons. (A length of
tubing is sometimes inserted into the meter body to prevent float
movement during shipping).
! Be sure the meter and the materials of construction are suitable for
your application.
! The maximum temperature and pressure is shown on the following
pages.
! Although the meter may be suitable for use with other fluids, Blue-
® White meters are tested with water and air only. If you are not sure
that the meter is compatible with your fluid, consult the factory.
! The meter can be damaged by UV light. Do not install the meter in
direct sunlight.
® ! Blue-White guarantees the meter is suitable with air and water
only.