NSi Industries W100 - Manual (Page 5)

TORK MODEL W220L
SEVEN DAY CALENDAR DIAL TIME SWITCH
SWITCH: DPDT
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
SYNCHRONOUS POWER WITH RESERVE:
Should your power supply be interrupted, this switch
will continue to operate on time for several hours.
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON trippers close circuits 1 and 3.
OFF trippers close circuits X and 5. Dial is graduated in one hour
intervals. There must be an ON and an OFF tripper for each day of
the week operations are desired. Place tripper on dial edge as
shown in diagram. Set point of each tripper at the desired operating
time. Hold tripper securely against dial and tighten knurled screw
firmly by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes.
DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close cir-
cuit. Press down lever on left of nameplate to open it.
Disconnect power at main panel prior to installing or servicing this time switch or the equipment
connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C (167 degrees F)
TORK ®
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
LI-604(A)
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER W
E
D
TUE
N
S
E
T
M
ID
NIG
HT
MIDNIGHT
MI
DN
IG
H T
NO
ON ON
A
M
P M
A M P M
A M
P
M
OFF
ON
T
I
M
E 9
7
5
3
1
11
9
7 5
3 1 11
9 7 5 3 1 11 9 7 5 3 11 9 7
5 3
1
11
9
7
5
1 0
8
6
4
2
12
10
8
6 4 2 12 10 8
6 4 2 12 10 8 6 4 2 1 2 1 0 8 6
4
2
12
10
8
6
4
O
F
F O
N
TORK ➤ MANUAL
ON
LEVER
MANUAL
OFF
LEVER
TIME
➤
Typical connections for 120VAC.
1 X 2
L 3 4 5
LOADS
CHARGE
CARGA
N
LOADS
CHARGE
CARGA
H
H
N
H
N
FRONT
REAR
L
FRONT
FRENTE
ARRIÉRE
ESPLADA
MOTOR
MOTEUR