NSi Industries E103P - Manual (Page 2)

TO SET SCHEDULE
If display does not show SCH, press mode key until display shows SCH.
Note: There are 7 ON and 7 OFF set points which alternate (set point #1
is ON; #2 is OFF; #3 is ON).
The display will Indicate it is ready to receive SCH setpoint #1 which is
an ON event.
Press HOUR and MIN keys for the first ON setting (check for AM or PM).
Press ENTER key to store the information and display will indicate it is
ready to receive SCH setpoint #2 which is an OFF event.
Press HOUR and MIN keys for the first OFF setting. Then press ENTER
key to store the information and display will indicate it is ready to
receive SCH setpoint #3 which is the next ON event.
Proceed for up to 7 ON and 7 OFF setpoints. Then press MODE key and
unit will go to the AUTO (run) mode.
In the AUTO mode, the unit will display current time and day as well as
load status (ON and OFF).
Note: When the unit is returned to the auto mode, check the load status of the cur-
rent setting. If it is showing OFF but should be ON, press the override key. The unit
will correct itself at the next scheduled event and no further alteration will be neces-
sary.
REVIEW/MODIFY
1. CLOCK - ALTER TIME
Press mode key until display shows CLK.
Press DAY, HOUR, and MIN keys to change to the correct time. Press
ENTER.
2. SCHEDULE - REVIEW
Press mode key until display shows SCH.
Press ENTER key repeatedly to review all the scheduled entries.
3. SCHEDULE - MODIFY
During the review (see previous section) any setpoint can be modified or
deleted. Use the HOUR and MIN keys to modify. Use the DELETE key to
eliminate that event. Press ENTER key after each modification.
OVERRIDE - TEMPORARY
In order to temporarily change the current ON or OFF status of a load,
simply press the override key when the unit is in the AUTO mode. The
altered load status will flash. Override is in effect until the next scheduled
event. In order to cancel the override, press override key again.
OVERRIDE - LONG TERM
Press mode key until display shows MAN (manual). Normal schedule
will not be executed and the load status will remain unchanged as
indicated. Press the OVERRIDE key to obtain the correct status or
to alter the load status.
TORK
DIGITAL TIME SWITCH
Type 1 Indoor Enclosure
®
UL
469D
LISTED
®
LR21743
DRY CONTACT RATINGS
30A
30A
6A
5A
470VA
2 HP
12A
12A
6A
5A
690VA
–
Type
of Load
120
VAC
240
VAC
277
VAC
20A Resistive @ 28VDC
Resistive
Inductive
Ballast
Tungsten
Pilot Duty
Motor
30A
30A
20A
5A
470VA
1 HP
3
SPST
4
LOAD
S
1 2
N L N
TIMER
SUPPLY
E101P E103P E120P
OUTPUT:
E101P (SPST)
INPUT: 120VAC,
SPECIAL ENCLOSURE:
-C -Y -FLG
DPST TIMER
SUPPLY
3 5 6 4
L L N
1 2
LOAD
N
LOAD
N
OUTPUT:
E103P (DPST)
DRY CONTACT RATINGS
Resistive
Inductive
Ballast
Tungsten
Pilot Duty
Motor
20A
20A
6A
5A
1 HP
Type
of Load
120VAC 240VAC 277VAC
N.O. 20A Resistive @ 28VDC
N.O. N.C N.O. N.C N.O. N.C
470
VA
10A
10A
3A
3A
275
VA
20A
20A
6A
5A
2 HP
470
VA
10A
10A
3A
3A
275
VA
6A
6A
6A
–
–
690
VA
3A
3A
3A
–
–
–
1/4
HP
1/2
HP
N.C. 10A Resistive @ 28VDC
TIMER
SUPPLY
3 4 5
SPDT
1 2
L N
LOAD LOAD
N N
E120P
E101P &
E103P
OUTPUT:
E120P (SPDT)
TORK ®
MLI-157(B) 1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
WARNING !
Lockout power at main panel before initial wiring or servicing
of this time switch and any equipment connected to it. More
than one disconnect point may be required. Install and use in
accordance with national and local electrical codes. Use cop-
per wire AWG #10-16 suitable for 75°C (167°F). Metal enclo-
sure must be properly grounded. Insulator must be
replaced below before
turning on electricity.
Inform electrician if it
is missing.
E100P MANUAL 11/18/03 5:00 PM Page 1