Vitrex MIX1400 - Manual (Page 3)

1400W Power Mixer
04 05
Tel: +44 (0) 1253 789180 Tel: +44 (0) 1253 789180
HOW TO USE THE MIXER
Before setting up, repair or maintenance of the appliance
you must always turn off the operating switch and pull out
the mains plug!
Before Initial Operation
• Check if the rated frequency of the mains supply
corresponds to the details of the type place.
• Before using the tool, read the instruction book carefully.
Mixer Assembly (Fig. 2):
First screw mixer part (6a) together with mixer part (6b).
Screw the mixer (6) into the mixer holder (5) afterwards.
Use the two spanners to do this. Use one of the spanners
(a) to hold the mixer holder (5) in place and then use the
second spanner (b) to tighten up the mixer (6). Proceed in
the reverse sequence to undo the mixer.
The paddle’s shape could be different and not necessary
the same as above picture shows.
Starting the machine
On/Off switch:
Switching on: Press the switch Fig 1(1)
Continuous running:
Press the locking knob on the switch Fig 1(1) (2) to lock it
in place
Switching off:
Press the switch Fig 1 (1) briefly
Speed control:
Use the speed control Fig 1(3) to select the speed.
Switching between 1st - 2nd gear Fig 1(4)
The switch position enables you to work at high or low
speeds. The gear switch position should only be changed
when the unit is stopped, in order to prevent the gearing
from being damaged.
• 1st gear
• 2nd gear
Working With the Paint and Mortar Mixer
The mains plug must be disconnected before the mixing
tool is changed.
The unit should be run at low speed before it is immersed
in or removed from the mixture. The speed should only be
increased to maximum after it has been fully immersed in
the mixture, in order to ensure that motor is kept as cool
as possible. The machine must be moved around inside
the mixing vessel during the mixing process. Continue the
mixing process until all of the mixing components have
been processed.
Always clean the mixer after you have finished using it.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or
battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites
accidents.
d) Remove any adjusting key or spanner before turning
the power tool on. A spanner or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
PRECAUTIONS ON USING MIXER
• The equipment must never be used in surroundings
where an explosive atmosphere exists. Never mix in
solvents or substances containing solvent that have flash
points below 21°C.
•Do not let the cable touch any parts of your body.
• Only use the extension cable approved for use in the
working area.
• The unit must only be started and stopped when it is
inside a mixing vessel. Ensure that the mixing vessel is
placed on a solid, secure base.
• Never reach into the mixing vessel with your hands or
any other object during the mixing process.
• We recommend that you always wear industrial safety
gloves and safety goggles when working with the mixer.
• Wearing close-fitting clothes is mandatory.
• Always allow for reaction torque
• Always wear a dust mask