Arcam Handbook AVR surround amplifier/AV processor AVR600 - Manual (Page 61)

E-59
English
Device codes
The tables that begin on page 64 (in the final section of
this Handbook) list the four-figure codes for different
manufacturers’ devices.
Use these when setting your CR102 up to control your
devices, as described in Method 1 (see page 30).
If more than one code number is listed, try the first
number. If the results are unsatisfactory, continue trying
the numbers for that manufacturer to get the best ‘fit’
with the functionality required.
If the manufacturer of your equipment is not listed, you
can try Method 2, the Library Search (see page 30). This
allows you to scan through every set of codes contained
in the CR102’s memory.
Command summary
direct code setup
(e.g. AV mode, NNNN=code number)
a
S * * NNNN * * P
Library search
(e.g. AV mode)
a
S 9 9 1 * * P [ until unit turns off
S to save
Code blink back
a S 9 9 0 **
1 count blinks for first N
2 count blinks for second N
3 count blinks for third N
4 count blinks for fourth N
Code learning
(e.g. AV mode fast forward key)
S
* * 9 7 5 * * a ( * (many
rapid blinks)
(Press key on original remote that you wish to copy)
*
* S * *
delete a learned function
(e.g. AV mode fast forward key)
S
* * 9 7 5 * * a ( ( * *
delete all learned functions with a device
(e.g. AV mode)
S
* * 9 7 5 a a
Creating macros
(e.g. SRCH key)
S
* * 9 9 5 h a P w P z P S
* *
deassign macro
S * * 9 9 5 h S * *
key mover
(e.g. SAT mode, DISP key to MENU key)
z
S * * 9 9 4 D U
Mode mover
(e.g. change SAT to TV(AV))
S
* * 9 9 2 a z
Restore device mode
(e.g. restore SAT)
S
* * 9 9 2 z z
Locking/unlocking a mode
(e.g. DVD mode)
d
S * * 9 8 2 * *
(i.e. two blinks for lock)
d
S * * 9 8 2 * * * *
(i.e. four blinks for unlock)
Cancel all volume punch-through
S * * 9 9 3 + * * * *
Restore volume punch-through
S * * 9 9 3 A * *
Mode key IR punch-through
S * * 9 7 1 * * A
Cancel mode key IR punch-through
S * * 9 7 1 * * S * *
NOTE
As elsewhere in this Handbook, a single ‘blink’ of
the red LED behind the power button is indicated
by the symbol * .
Mode key IR punch-through
The Mode key IR punch-through default is ‘on’.
Example: To set the Mode key IR punch-
through to aMP
1. Press and hold S until the power LED blinks twice:
* *.
2. Press 9 7 1. The power LED blinks twice: *
* .
3. Press A to punch through IR from it.
Now, whenever you press and release a Mode key, the
IR data assigned to AMp is transmitted, no matter what
the current mode is (i.e. it ‘punches through’ any other
device).
To cancel Mode key IR punch-through
1. Press and hold S until the power LED blinks twice:
* *.
2. Press 9 7 1. The power LED blinks twice: *
* .
3. Press S until the power LED blinks twice: * *.
Resetting the CR102
Resetting the CR102 will erase all learned functions
across all modes, as well as some other programmed
functions like Macros. It will not reset the Device Mode
keys; these will remain programmed to your choice of
component.
1. Press and hold S until the power LED blinks twice:
* *.
2. Press 9 8 0. The power LED blinks four times:
* * * *.
3. Press and hold S until the power LED blinks twice:
* *.
4. Press 9 9 3.
5. Press A. The power key LED blinks twice: * *.
6. Press and hold S until the power LED blinks twice:
* *.
7. Press 9 7 1. The power LED blinks twice: *
* .
8. Press A. The power key LED blinks twice: * *.