Wright Serial 54956 and higher - Manual (Page 3)

3
Table of Contents
PRE-DELIVERY SERVICE OF MOWER BY DEALER ...................................................................................................................................... 4
1 INTRODUCTION
.......................................................................................................................................................................... 6
1.1 T ECHNICAL D ATA .................................................................................................................................................................................... 6
1.2 G ENERAL S AFETY R ULES ...................................................................................................................................................................... 6
1.2.1 D O’S AND D ON’TS ................................................................................................................................................................................. 7
1.3 W ARNINGS ................................................................................................................................................................................................ 7
1.4 I MPORTANT I NFORMATION ..................................................................................................................................................................... 7
1.5 S AFETY FOR O PERATION ....................................................................................................................................................................... 7
1.6 U SER Q UALIFICATIONS ........................................................................................................................................................................... 8
1.7 U SER C LOTHING ...................................................................................................................................................................................... 8
1.8 I NSPECT THE M OWER B EFORE E ACH U SE ......................................................................................................................................... 8
1.9 R EGULAR M OWER S AFETY .................................................................................................................................................................... 8
1.10 W ORK A REA C ONDITIONS AND I NSPECTION .................................................................................................................................... 9
1.11 I NITIAL O PERATING S AFETY G UIDELINES ......................................................................................................................................... 9
1.12 S AFETY FOR M AINTENANCE .............................................................................................................................................................. 10
1.13 O PERATION IN F ORWARD D IRECTION ............................................................................................................................................. 10
1.14 O PERATION IN R EVERSE ................................................................................................................................................................... 10
1.15 Z ERO -R ADIUS T URN O PERATION ..................................................................................................................................................... 10
1.16 O PERATION ON S LOPES .................................................................................................................................................................... 10
1.17 F UEL S AFETY ....................................................................................................................................................................................... 11
1.18 USING A SPARK ARRESTER ................................................................................................................................................................ 12
1.19 R EPLACEMENT P ARTS ....................................................................................................................................................................... 12
2 W ARNING , S AFETY AND I NSTRUCTIONAL D ECALS ............................................................................................................................. 13
3 SPECIFICATIONS ........................................................................................................................................................................................ 13
4 MACHINE DESCRIPTION & OVERVIEW .................................................................................................................................................... 15
4.1 O PERATOR’S A REA ............................................................................................................................................................................... 16
4.2 M ODEL & S ERIAL L OCATION ................................................................................................................................................................ 16
4.3 C ONTROL P ANEL & S TEERING C ONTROL L EVERS ........................................................................................................................... 17
4.4 F UEL S YSTEM / S HUT -O FF V ALVE ...................................................................................................................................................... 17
5 OPERATING INSTRUCTIONS ..................................................................................................................................................................... 18
5.1 I NSPECT M OWER B EFORE E ACH U SE ............................................................................................................................................... 18
5.2 H OW TO S TART THE M OWER .............................................................................................................................................................. 18
5.3 H OW TO S TOP AND P ARK THE M OWER ............................................................................................................................................. 19
5.4 H OW TO D RIVE THE M OWER O VER A C URB ..................................................................................................................................... 19
5.5 M OWING O VER V ARYING T ERRAIN .................................................................................................................................................... 19
5.6 H OW TO A DJUST THE S PEED .............................................................................................................................................................. 19
5.7 S TRAIGHT L INE T RACKING A DJUSTMENTS ....................................................................................................................................... 19
5.8 H OW TO T EST /U SE THE B LADE C LUTCH /B RAKE S WITCH .............................................................................................................. 20
5.9 H OW TO T EST THE O PERATOR P RESENCE C ONTROL (OPC) S WITCH ........................................................................................ 20
6 SERVICE AND ADJUSTMENTS ................................................................................................................................................................. 21
6.1 T IRE M AINTENANCE AND P RESSURE ................................................................................................................................................. 21
6.2 B ELT T ENSION A DJUSTMENT .............................................................................................................................................................. 21
6.2.1 R EPLACING THE D RIVE B ELT ........................................................................................................................................................... 21
6.2.2 R EPLACING THE C UTTER D ECK B ELTS .......................................................................................................................................... 22
6.3 L UBRICATION ...................................................................................................................................................................................... 22
6.4 C UTTING B LADES ................................................................................................................................................................. 23
6.5 S PINDLE AND D RIVE P ULLEY S PLIT H UB R&R .................................................................................................................... 23
6.6 B LADE A DJUSTMENTS AND H EIGHT - OF -C UT .................................................................................................................... 23
6.7 M OVING THE M OWER WITH THE E NGINE O FF................................................................................................................................... 24
6.8 T RANSPORTING ................................................................................................................................................................. 24
6.9 L OADING AND U NLOADING ................................................................................................................................................. 24
6.10 C LEANING THE M OWER ..................................................................................................................................................... 24
6.11 FUEL EVAPORATION SYSTEM ............................................................................................................................................................ 25
6.12 KAWASAKI ENGINE MANUAL / MAINTENANCE ................................................................................................................................... 26
7 ELECTRICAL SCHEMATICS ................................................................................................................................................. 27
8 MAINTENANCE INTERVAL CHART ..................................................................................................................................... 28
MAINTENANCE RECORD ........................................................................................................................................................ 29
W RIGHT M ANUFACTURING P OWER E QUIPMENT L IMITED W ARRANTY............................................................................................... 30
F EDERAL AND C ALIFORNIA E MISSION C ONTROL W ARRANTY STATEMENT ...................................................................................... 31
CUT QUALITY AND MOWING TIPS ......................................................................................................................................... 33