Volant CRTi2-8.63 - Manual (Page 2)

1 Tool hoist rating is based on API Specification 8C; however, casing load limit is further constrained by local interaction of slip dies with casing, which must not exceed the
efficiency indicated for individual slip die sizes to avoid excessive deformation. The slip to casing interaction hoist limit is calculated by multiplying the slip to pipe body load
efficiency number by the casing hoist limit found in API Bulletin 5C2. From 5C2 the pipe body yield for 9.63” x 40.0 ppf L-80 Casing is 916,000 lbs. The slip efficiency for die
81756 used to run this casing on the CRTi2-8.63 tool is 80%. Therefore, the casing hoist limit is 80% x 916,000 lbs = 732,800 lbs or 366.4 tons.
2 CRTi hoist capacity must be reduced by the pressure end load during circulation.
3 Torque capacity may be limited by slip die/casing interaction. Where torque factors are provided, multiply this factor by the desired casing weight in ppf then multiply the result by
the casing yield strength to determine the slip die/casing interaction torque limit. If no value is provided, tool rating will be limiting for all standard casing grades.
4 Maximum allowable compressive (push down) load applied to the tool. Some compressive load may be reacted through the coupling. This rating does not take into account
bearing load limitations of the coupling.
5 CRTi circulation pressure capacity is generally governed by packer cup pressure capacity. Pressure capacity may be less than indicated if alternative seal arrangements are used.
6 Overall tool length depends on seal arrangement.
7 Maximum flow rate is based on minimizing erosion rates when using typical fluids. Erosion rates may vary based on fluid contents. Please inspect tool bore regularly.
8 Common die sizes shown. Dies are available for all API casing sizes and weights with drift diameter above 7.38” are available.
9 Maximum pipe weight is defined by the API Specification 5CT drift diameter of the heaviest weight casing into which the CRTi assembled with the specified die set will fit.
10 Indicated minimum pipe weight is based on the assumption that control of average pipe inside diameter over die grip interval does not allow pipe body area reduction
less than 3.5% from nominal and additionally takes into account tool wear allowances, die penetration, casing deformation and tool stroke.
Casing Running Tools (CRTi 2-8.63)
Nom. Max. Pipe Min. Pipe Die Curv. Max. Tool Slip to Pipe Body Torque
Die P/N Pipe Size Weight 9 Weight 10 Diameter Diameter Tool Weight Load Eff. 1 Factor 3
(in) (ppf) (ppf) (in) (in) (lbs) (% Fy) (ft*lb/psi/ppf)
81024 8.63 36.0 24.0 8.04 20.0 1,350 80% 0.029
82301 9.63 32.0 32.0 9.19 20.0 1,350 80% 0.028
81756 9.63 43.5 32.0 8.91 20.0 1,350 80% 0.024
81154 9.63 53.5 40.0 8.71 20.0 1,350 80% 0.029
81881 9.63 58.4 47.0 8.6 20.0 1,350 80% 0.031
82276 10.75 40.5 32.75 10.22 20.0 1,500 80% 0.025
82275 10.75 51.0 40.5 10.02 20.0 1,500 80% 0.025
81255 10.75 65.7 51.0 9.73 20.0 1,500 80% 0.026
81494 10.75 73.2 60.7 9.57 20.0 1,500 80% 0.027
81138 10.75 79.2 71.1 9.4 20.0 1,500 80% 0.028
81495 11.75 60.0 47.0 10.94 20.0 1,600 80% 0.023
81757 11.75 71.0 60.0 10.75 20.0 1,600 80% 0.023
82039 12.75 58.4 50.0 12.03 20.0 1,850 71% 0.020
82168 13.38 54.5 48.0 12.78 20.0 2,100 74% 0.020
81897 13.38 61.0 48.0 12.68 20.0 2,100 74% 0.020
82164 13.38 68.0 54.5 12.58 20.0 2,100 75% 0.021
81150 13.38 72.0 61.0 12.52 20.0 2,100 75% 0.021
82588 13.38 77.0 61.0 12.44 20.0 2,100 75% 0.021
81431 16.0 65.0 65.0 15.42 20.0 2,500 59% 0.016
81645 16.0 84.0 75.0 15.18 20.0 2,500 63% 0.018
82100 16.0 97.0 84.0 15.03 20.0 2,500 61% 0.017
81758 16.0 109.0 97.0 14.88 20.0 2,500 64% 0.018
82532 16.77 77.0 69.4 16.09 20.0 2,600 55% 0.015
81752 17.88 105.0 93.5 16.96 20.0 2,650 53% 0.015
81434 18.63 87.5 87.5 17.88 20.0 2,800 45% 0.013
81566 18.63 97.7 87.5 17.85 20.0 2,600 55% 0.015
82101 18.63 111.0 97.7 17.71 20.0 2,600 55% 0.015
82675 18.63 117.0 111.0 17.63 20.0 2,600 56% 0.015
81880 18.63 139.0 136.0 17.39 20.0 2,600 56% -
81759 20.0 106.5 94.0 19.19 20.0 3,000 49% 0.014
81483 20.0 133.0 129.3 18.92 20.0 3,000 50% 0.014
82740 20.0 169.0 166.4 18.58 20.0 3,000 52% -
82102 22.0 184.5 184.5 20.53 28.0 3,100 45% -
81750 22.0 224.0 224.0 20.11 28.0 3,100 40% -
81462 26.0 275.0 275.0 24.09 28.0 3,700 37% -
82486 28.0 222.7 222.7 26.59 32.0 4,400 27% 0.008
82506 30.0 233.22 233.22 28.59 32.0 4,700 24% 0.007
Give us a problem. Or just drop us a line if you want to know more.
+1 866.8VOLANT / +1 866.886.5268 +1 780.784.7099 [email protected] volantproducts.ca
Document No. 20007 / Revision L Printed in Canada APRIL 2013
Summary of Selected Slip Die Sizes 8
CRTi2-8.63 | PAGE 2