Qualcraft Side Wall Staging Bracket - Manual (Page 3)

SIDE WALL STAGING BRACKET
MODEL #2300, #2301
CONSTRUCTION
PRODUCTS
the 2x4 that spans the interior studs. With the cross brace securely span-
ning the two interior studs attach the handle to the bolt and tighten until
bracket is fi rmly in place. Be sure that the staging bracket is in a vertical
position to ensure proper bracing. Nail brace at base into the work wall.
Install guardrail holder to end of platform. Choose location for next staging
bracket that is no more than 8 feet from previously installed bracket and
repeat installation procedures for bracket. Fully plank the work platform
and install all guardrails. When installing staging on sheathing that is less
than 3⁄4 inch in thickness provide a 5/8 inch plywood sheet large enough
to span two studs and high enough to encompass both the bolt at the top
of the bracket and the brace at the bottom of the bracket and secure to
the exterior sheathing prior to the installation of the bracket.
CARE & MAINTENANCE: Inspect staging brackets, guardrails and walk
planks before and after each use to be sure there is no damage or defor-
mation of any of the scaffold components. Also inspect to be sure there
is no deterioration as a result of rusting. Discard if necessary. Always
handle staging brackets and guardrails with care to ensure safe and last-
ing use of the equipment. Do not throw or drop from a building or onto a
truck. Always handle with care. If staging or guardrail equipment has been
exposed to extreme heat or cold, discard equipment. Use this product
in strict compliance with all State, Local and Federal OSHA Regulations.
Federal Regulations require that your employer provide training in the use
and care of this product
.
To prevent an unstable scaffold that could lead to serious personal injury:
•Do not install directly onto walls constructed of sheathing materials other than 3⁄4” thick
exterior grade plywood.
•When used on sheathing material other than 3⁄4” thick exterior grade plywood read and
follow instructions.
Failure to read and follow instructions on the use of this product could result in serious
personal injury. This product must be used in strict compliance with Local, State & Federal
OSHA Regulations. Be safety conscious.
Installing
Staging Bracket Guardrail
Holder
Model # 2301
The Qual-Craft Model # 2301 Staging
Bracket Guardrail Holder should be installed
prior to mounting the model #2300 Staging
Bracket to the work wall. Lay the base of
the guardrail holder up under the end of the
staging bracket platform so that the guardrail
holder is at right angle to the platform arm.
Line up the holes in the base of the guardrail
with the corresponding holes in the staging
bracket. Secure in place with four 3/8”-16
x 3⁄4” hex bolts and four 3/8”-16 reversible
lock nuts. Repeat installation procedure with
each of the staging brackets that will form the
completed scaffold. Install all staging brackets
(with guardrail holder attached) to the work wall
in accordance with the instructions affi xed to
the Model #2300 Staging Bracket. Fully deck
the scaffold and secure in place. Install 2” x
4” wooden guardrails, mid-rails and 1” x 3”
wooden toe boards. Guardrails, mid-rails and
toe boards must run the complete perimeter
of the deck and must be secured to the work
wall. To insure a ridged guardrail system it is
important to use all nail holes provided at each
receptacle.
Care & Maintenance
Inspect staging brackets, guardrails and walk
platforms before and after each use to be sure
there is no damage or deformation to any of
the scaffold components. Also inspect to be
sure there is no deterioration as a result of
rusting. Discard if necessary. Always handle
staging brackets and guardrails with care to
insure safe and lasting use of this equipment.
Do not throw or drop from a building or onto a
truck. If staging bracket or guardrail equipment
has been exposed to extreme heat or cold
discard equipment. Use this product in strict
compliance with all State, Local and Federal
OSHA Regulations. Federal regulations require
that your employer provide training in the use
and care of this product.
© Copyright 2001 QUAL-CRAFT INDUSTRIES, INC. Stoughton, MA 02072
Customer Supprt and Ordering In for ma tion
781-344-1000 • www.qualcraft.com