Lincoln Electric IM10082 VIKING 1840 SERIES AUTO-DARKENING HELMETS - Manual (Page 7)

CARTRIDGE OPERATION/FEATURES
Variable Shade Control
The shade can be adjusted from shade 9 to 13 based upon welding process or
application (refer to Shade selection chart on page 6). The variable shade control
knob is mounted on the exterior of the helmet shell. Grind mode can be selected
by rotating the shade control knob counterclockwise till an audible click is heard.
Grind mode is intended for grinding only not for welding.
Sensitivity Knob
You can adjust the light sensor by turning the Sensitivity knob to the left or right as
shown in figure below. Generally, turning the knob all the way to the right, or the
highest setting, is selected for normal use. When the helmet is used in the pres-
ence of excess ambient light or with another welding machine close by, improved
helmet performance can be obtained with a lower setting turning the knob to the
left to reduce the sensitivity.
Delay Time Knob
This control is designed to protect the welder’s eyes from the strong residual
rays after welding. Changing the Delay Time knob will vary dark to light time
between 0.1 second (minimum) to 1.0 second (maximum). Turning the Delay
Time knob to the left is maximum (1.0 second). This setting is recommended for
high amperage applications where the weld puddle is still very bright after the
welding arc has ceased and for situations where the filter may be temporarily
blocked from seeing the welding arc.
Solar Power
This helmet is powered by solar energy. There are no user replaceable batteries.
Variable shade
Control Knob
5
ANSI Z87.1 CAN/CSA Z94.3 LABS S 2 7 9 7 8 -6 SENSITIVITY DELAY TIME 4/9-13 TM 1/1/1/2 EN379 700G / 1840 ADF
ANSI Z87.1
CAN/CSA Z94.3
LABS
S2
79
78
-6
SENSITIVITY DELAY TIME
4/9-13 TM 1/1/1/2 EN379
700G / 1840 ADF
ALWAYS TEST TO BE SURE THE ADF CARTRIDGE IS CHARGED
BEFORE WELDING. The helmet can be placed in sunlight to charge. Do
not store the helmet in a dark cabinet or other storage area for long periods.
While welding, the arc also charges the ADF cartridge.
SHADE GUIDE SETTINGS
If your helmet does not include any one of the shades referenced above, it is
recommended you use the next darker shade.
6
NT1 GUIDE FOR SHADE NUMBERS OPERATION ELECTRODE SIZE ARC MINIMUM SUGGESTED(1) 1/32 in. (mm) CURRENT (A) PROTECTIVE SHADE NO. SHADE (COMFORT) Shielded metal arc Less than 3 (2.5) Less than 60 7 – welding 3-5 (2.5–4) 60-160 8 10 5-8 (4–6.4) 160-250 10 12 More than 8 (6.4) 250-550 11 14 Gas metal arc Less than 60 7 – welding and flux 60-160 10 11 cored arc welding 160-250 10 12 250-500 10 14 Gas tungsten arc Less than 50 8 10 welding 50-150 8 12 150-500 10 14 Air carbon (Light) Less than 500 10 12 Arc cutting (Heavy) 500-1000 11 14 Plasma arc welding Less than 20 6 6 to 8 20-100 8 10 100-400 10 12 400-800 11 14 Plasma arc cutting (Light) (2) (2) (2) Less than 300 8 9 (Medium) 300-400 9 12 (Heavy) 400-800 10 14 Torch brazing – – 3 or 4 Torch soldering – – 2 Carbon arc welding – – 14 PLATE THICKNESS in. mm Gas welding Light Under 1/8 Under 3.2 4 or 5 Medium 1/8 to 1/2 3.2 to 12.7 5 or 6 Heavy Over 1/2 Over 12.7 6 or 8 Oxygen cutting Light Under 1 Under 25 3 or 4 Medium 1 to 6 25 to 150 4 or 5 Heavy Over 6 Over 150 5 or 6 (1) As a rule of thumb, start with a shade that is too dark, then go to a lighter shade which gives sufficient view of the weld zone without going below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs the yellow or sodium line the visible light of the (spectrum) operation (2) These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the workpiece. . Data from ANSI Z49.1-2005
NT1
GUIDE FOR SHADE NUMBERS
OPERATION ELECTRODE SIZE ARC MINIMUM SUGGESTED(1)
1/32 in. (mm) CURRENT (A) PROTECTIVE SHADE NO.
SHADE (COMFORT)
Shielded metal arc Less than 3 (2.5) Less than 60 7 –
welding 3-5 (2.5–4) 60-160 8 10
5-8 (4–6.4) 160-250 10 12
More than 8 (6.4) 250-550 11 14
Gas metal arc Less than 60 7 –
welding and flux 60-160 10 11
cored arc welding 160-250 10 12
250-500 10 14
Gas tungsten arc Less than 50 8 10
welding 50-150 8 12
150-500 10 14
Air carbon (Light) Less than 500 10 12
Arc cutting (Heavy) 500-1000 11 14
Plasma arc welding Less than 20 6 6 to 8
20-100 8 10
100-400 10 12
400-800 11 14
Plasma arc cutting (Light)
(2)
(2)
(2) Less than 300 8 9
(Medium) 300-400 9 12
(Heavy) 400-800 10 14
Torch brazing – – 3 or 4
Torch soldering – – 2
Carbon arc welding – – 14
PLATE THICKNESS
in. mm
Gas welding
Light Under 1/8 Under 3.2 4 or 5
Medium 1/8 to 1/2 3.2 to 12.7 5 or 6
Heavy Over 1/2 Over 12.7 6 or 8
Oxygen cutting
Light Under 1 Under 25 3 or 4
Medium 1 to 6 25 to 150 4 or 5
Heavy Over 6 Over 150 5 or 6
(1)
As a rule of thumb, start with a shade that is too dark, then go to a lighter shade which gives sufficient view of the weld zone without going
below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs
the yellow or sodium line the visible light of the (spectrum) operation
(2) These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the
workpiece.
.
Data from ANSI Z49.1-2005