LiftMaster MH Medium-Duty Hoist Operator - Manual (Page 2)

TTC
LED
AUX ANT
R27
L5
TP1 C20
C9
C29
R24
J2
C21
J4
K2
LT
P1
C32
U4 D7
D6
D5
D4
R25
U1 C31
D14
C18
014A1030
^^^^
D9
LEARN
1 2 3 4 5 6 7
LMEP1 LMEP2 INTRLK COM STOP CLOSE OPEN
STOP CLOSE OPEN
AUX ANT
© 2009, The Chamberlain Group Inc.
All Rights Reserved
01-34219
This QuickStart is intended to highlight a typical installation. These instructions are not intended to be comprehensive. Since each application is unique, it is the
responsibility of the purchaser, designer, installer and end user to ensure that the total door system is safe for its intended use. Please consult the manual and/or a
qualified technician for further information.
NOTE: Intended for Professional Installation Only. Visit www.liftmaster.com to locate a professional installing dealer in your area.
AN ENTRAPMENT PROTECTION DEVICE IS HIGHLY RECOMMENDED
CONTROL WIRING
USE COPPER WIRE ONLY
16-22 AWG
COM INTRLK STOP OPEN CLOSE
1
LMEP1 LMEP2
2 3 4 5 6 7
Direction Limit Nut Will Move During Travel
Retaining Plate
Limit Nuts
Push
SAFETY
CLOSE
OPEN
115 V PH. 1 Power Connection
9
14 AWG Minimum
POWER WIRING
USE COPPER WIRE ONLY
Power
Wiring
ONLY!
Follow ALL local electrical codes
L1 L2
LiftMaster Monitored Entrapment
Protection (LMEP)
White/Black
White
PROGRAMMING
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
AUX ANT ^^^^ AUX ANT AUX ANT D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN 1 LMEP1 LMEP2 2 3 4 5 6 7 STOP CLOSE OPEN
REMOTE CONTROLS
Built in 315 MHz radio receiver permits as many as 20 Security
✚
® remote controls or dip switch
remote controls in any combination.
Single Button Remote Control
1 Press and release the LEARN
button (LED will light). 2 Press and hold the button on the remote
control until the LED flashes rapidly, then
release to complete programming
(LED will go out).
3-Button Remote Control to Operate as a Wireless 3-Button Control Station
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
AUX ANT ^^^^ AUX ANT AUX ANT D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN 1 LMEP1 LMEP2 2 3 4 5 6 7 STOP CLOSE OPEN
1 Press and release the LEARN
button (LED will light).
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
Press the desired button on the logic board
(OPEN, CLOSE or STOP). Release both buttons. 2 3 Press and hold the desired button of
the remote control until LED flashes
rapidly, then release.
Repeat steps 1 and 2 for additional remote controls.
To Erase All Remote Controls
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
1 Press and hold the LEARN button (over 5
seconds) until the LED goes out. All
programmed remote controls will be erased.
TIMER-TO-CLOSE
Timer-to-Close feature enables the operator to close from the open limit after a preset time, adjustable from 5 to 60 seconds.
To Program
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
AUX ANT ^^^^ AUX ANT AUX ANT D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN 1 LMEP1 LMEP2 2 3 4 5 6 7 STOP CLOSE OPEN
1 Press and release the LEARN
button (LED will light). 2
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
Press and release the TCC
button. 3 Every press and release of the STOP button
will add 5 seconds to the Timer-to-Close.
Example: 30 second TTC = 6 presses of the
STOP button.
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
4 Press and release the TTC button
to exit programming mode.
The LED will flash once per 5
seconds of timer setting.
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
To Verify the Timer-To-Close (TCC) Setting
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
AUX ANT ^^^^ AUX ANT AUX ANT D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN 1 LMEP1 LMEP2 2 3 4 5 6 7 STOP CLOSE OPEN
1 Press and hold the LEARN
button (LED will light). 2
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
Press and release the TCC
button. 3
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
Press and release the TTC button a
second time. The LED will flash once
per 5 seconds of timer setting.
NOTE: The feature will use 3 of the 20 memory channels in the operator.
Repeat steps 1 through 3 to program additional buttons.
The TTC will become active after completion of the next open cycle.
NOTE: The LED does not indicate that timer is running.
Clear the Timer-To-Close (TCC)
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
AUX ANT ^^^^ AUX ANT AUX ANT D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN 1 LMEP1 LMEP2 2 3 4 5 6 7 STOP CLOSE OPEN
1 Press and release the LEARN
button (LED will light). 2
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
Press and hold the
TCC button for 6 seconds. 3
D14
COM INTRLK STOP
LED
OPEN CLOSE
TTC LEARN
1
LMEP1 LMEP2
2 3 4 5 6 7
STOP CLOSE OPEN R27
Release the TTC button (LED
will go out). The TTC will no
longer be active.
Timer Defeat
The TTC can be temporarily
disabled by pressing a STOP
button. TTC will become enabled
after the next open command. Begin with the door in fully closed position.
Requires LiftMaster Monitored Entrapment Protection (LMEP) device. See installation manual
for LiftMaster Monitored Entrapment Protection (LMEP) device selection and installation.
QuickStart
for the Model MJ/MH/MHS/MGJ Door Operator MEDIUM DUTY LOGIC
POWER WIRING
CONTROL WIRING
LIMIT SWITCHES