LEDGlow 7 Color Slimline LED Underbody Kit - Manual

7 Color Slimline Underbody Kit
Warning:
Please check your state and local laws before installing this LED underbody lighting kit. Every state has different policies and procedures in place regarding
aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this underbody kit. This kit is for off road use only.
Warning:
The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.
The control box that is used to power this lighting kit must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s
controller to fail. Any water damage or corrosion to this part will VOID all warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED UNDERBODY KIT.
Underbody Kit Includes:

(2) 36 Inch tubes (A & C)

(2) 48 Inch Tubes (B & D)

(1) Control Box

(1) 4 Button Wireless Remote

(8) Underbody Tube Brackets

(20) Zip Ties

(8) Large Screws
Underbody Installation
1. Arrange the tubes out on the ground and test the kit to ensure proper functionality before installing.
2. Temporarily power your kit with any 12 volt source to ensure it is functioning properly before you move forward with the installation. Simply connect the red
wire to the positive terminal and the black wire to any good ground source. Power the kit on to ensure full functionality. Once you have determined the kit is
functioning properly, remove the power from your kit.
3. Optional: Raise and support the vehicle.
4. Before mounting each tube, please refer to the schematic below to ensure correct placement and tube direction.
Note: Each underbody tube daisy chains to the
next with the included 6 feet of power wire and
modular connectors.
Note: Use the waterproof tape on all connectors
to ensure connections are not exposed to the
elements.
5. Once the kit is laid out properly and you have determined that it is functioning properly, you can proceed with the rest of the installation.
6. First, mount the front tube to your vehicle, with the male connector facing the passenger side, using the included mounting brackets and zip ties. Make sure the
tube is at least 8 inches away from any direct heat source and away from all moving parts. Use the included wire ties to secure the underbody tube to the
mounting bracket. IMPORTANT: DO NOT DRILL ANY HOLES OR ATTACH THE MOUNTING BRACKETS TO THE RADIATOR.
7. Second, mount the driver’s side tube, with the male connector facing the rear of the vehicle, to your vehicle using the included mounting brackets and zip ties.
A good mounting location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not
mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power
wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.
8. Next, mount the passenger’s side tube to your vehicle, with the male connector facing the rear of the vehicle, using the included mounting brackets and zip ties.
A good mounting location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not
mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power
wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.
9. Now, mount the rear tube to your vehicle, with the connector facing the rear of the vehicle, using the included mounting brackets and zip ties. Be extremely
aware of the location of brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the
exhaust and the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included wire ties to secure the underbody tube to
the mounting bracket.
10. Mount the underbody kit’s control box in a safe and secure location inside of your vehicle. Run the lead power wire from the front underbody tube through a
pre-existing hole with a grommet in your firewall to the control box. If you do not have a pre-existing hole in the firewall you can drill one, just be sure to use a
rubber grommet to ensure the lead wire is not cut or pinched.