Agilent Technologies 6012B EN - Manual (Page 10)

10 General Information
Option Description
100 Input power: 100 Vac + 6%, -10%; 48-63 Hz single phase.
120 Input power: 120 Vac +6%, -13%. 48-63 Hz single phase.
220 Input Power: 220 Vac +6%, -13%; 48-63 Hz, single phase.
240 Input power: 240 Vac +6%, -13%; 48-63 Hz, single phase.
800
908
Rack mounting kit
909 Flanges with Handles
Accessories
The System-II cabinet accessories listed below may be ordered with the power supply or separately from your local Agilent
Technologies Sales and Support Office (see list of addresses at rear of this manual).
For Agilent Models 6023A and 6028A
Agilent Part No Description
5062-3989 Front handle kit for 5-1/4 inch high cabinets
1460-1345 Tilt stand (1) snaps into standard foot on; must be used in pairs
5062-3977 Rack flange kit for 5-1/4 inch high cabinet (will be shipped with supply if ordered as Option 908)
5062-3983 Rack mount flange kit with handles
1494-0060 Rack slide kit, non tilting
5060-2865 Service kit, includes extenders for control and power mesh boards, three cables to allow GP-IB and
PSI boards to lie on table outside unit, and control board test connector.
5060-2866 FET service kit. Includes FETs and all components that should be replaced with FETs.
59510A Relay Accessory
59511A Relay Accessory (Polarity Reversing)
For Agilent Models 6023A and 6028A
For Agilent Models 6023A and 6028A
Agilent Part No Description
5062-3960 Rack mounting adapter kit for side mounting one 7-inch high cabinet, includes one rack flange and one
half-module width extension adapter. (Will be shipped with instrument if ordered as Option 908). This
rack mounting adapter kit is not compatible with front handle kit Agilent P/N 5061-3990).
5062-3961 Rack mounting adapter kit for center mounting one 7-inch high cabinet, includes one rack flange and
one quarter-module width extension adapter (two kits required), there will be surplus of hardware.
5062-3978 Rack flange kit for 7-inch high cabinet. Must be used with another half-module width unit of equal
depth with lock link kit 5061-9694. (Will be shipped if instrument is ordered as Option 800).
5061-9694 Lock link kit for joining units of equal depth, contains hardware for three side-by-side joints (four
units) and two over-under joints (three units). Locking cabinets together horizontally in a configuration
wider than one full module is not recommended. 5062-3978 and 5061-9694 will be shipped if Option
800 is ordered.
5062-3990 Front handle kit for 7-inch high cabinets. Corresponding flange kit is 5061-2072. This front handle kit
is not compatible with rack mounting adapter kit (Agilent PIN 5062-3960) or Option 908.
5061-2072 Flange kit to be used with front handle kit 5062-3990.
5062-3984 Rack mounting flange kit with handles for 7-inch high cabinet. Must be used with another half-module
width unit of equal depth with lock link kit 5061-9694.
5062-4003 Bail handle kit for carrying 7-inch high, half-module width cabinet.
1460-1345 Tilt stand (1) snaps into standard foot on instrument, must be used in pairs.
5062-3998 Support shelf bit for mounting on or more 7-inch high cabinets of any depth to 20 inches.
5062-4027 Front filler panel, half-module width, for 7-inch high cabinet on support shelf.
1494-0065 Slide kit for 5061-0098 support shelf.
06033-60005 Service kit, includes extenders for control and power mesh boards, three cables to allow GP-IB and
One additional User’s Guide
Service Manual 0L2
0B3
Rack mount kit for two units side by side (models 6023A and 6028A only)