Bosch Aspirateur sans sac BGS32200 Bosch Relyyy Technologie sans sac innovante SensorBagless - Manual (Page 38)

37
Vacuuming
!
Caution
Floor nozzles are subject to a certain amount of
wear, depending on the type of hard floors you have
(e.g. rough, rustic tiles). You must therefore check
the underside of the floor nozzle at regular intervals.
Worn undersides of floor nozzles may have sharp
edges that can damage sensitive hard floors, such as
parquet or linoleum. The manufacturer does not ac-
cept any responsibility for damage caused by worn
floor nozzles.
Fig. 9
Set the adjustable floor nozzle:
„ Rugs and carpets ==>
„ Hard floors/parquet ==>
If you are vacuuming up relatively large particles, make
sure that you vacuum them up successively and careful-
ly to ensure that the vacuum channel of the floor nozzle
does not become blocked.
If necessary, you should raise the nozzle in order to
better vacuum up the dirt particles.
Vacuuming with accessories
Fig. 10*
Attach the nozzles to the suction pipe or handle as re-
quired:
a) Crevice nozzle for vacuuming crevices and corners,
etc.
b) Upholstery nozzle for vacuuming upholstered furni-
ture, curtains, etc.
c) Upholstery nozzle with fixed brush ring for vacu-
uming window frames, cupboards, profiles, etc.
After use, reinsert the crevice nozzle and upholstery
nozzle into the accessories holder.
d) Professional crevice nozzle
Extra-long crevice nozzle for cleaning crevices, cor-
ners and narrow spaces, e.g. in a car.
e) Professional upholstery nozzle
For gently and thoroughly cleaning upholstered fur-
niture, curtains, etc.
For cleaning the professional upholstery nozzle, sim-
ply vacuum it using the handle.
f) Hard-floor nozzle for vacuuming hard floor coverings
(tiles, parquet flooring, etc.)
Cleaning the hard-floor nozzle
Fig. 11*
a) Vacuum the nozzle from below to clean it.
b) Use scissors to cut through threads and hairs wound
round the rollers and then vacuum them away.
Drill dust nozzle
Fig. 12*
•
Fasten the drill dust nozzle onto the handle and po-
sition it on the wall so that the drill hole opening on
the nozzle is placed directly over where the hole is
to be drilled.
•
Set the appliance to the lowest power level and then
switch it on.
•
The drill dust nozzle is held in the required position
by suction. Depending on the condition of the wall to
be drilled, you may need to adjust to a higher power
setting to ensure that the drill dust nozzle remains
in place.
During drilling, the fine dust is automatically vacu-
umed up.
Turbo brush
If your appliance is equipped with a turbo brush, refer
to the accompanying instruction manual for instruc-
tions on its use and maintenance.
Fig. 13
You can use the parking aid on the back of the vacuum
cleaner if you want to stop vacuuming for a short time.
•
After switching off the appliance, slide the hook on
the floor nozzle into the parking aid.
Fig. 14
When vacuuming stairs, the appliance must be positi-
oned at the bottom of the stairs. If it does not reach
far enough, the appliance can also be carried using the
carrying handle or the handle on the dust container.
After vacuuming
Fig. 15
•
Switch off the appliance.
•
Remove the main plug.
•
Briefly pull on the power cord and then let go.
(The power cord retracts automatically.)
Fig. 16*
•
Unlock the telescopic tube by moving the sliding
switch in the direction of the arrow, and slide one
tube into the other.
Fig. 17
To store the appliance, use the storage aid on the un-
derside.
a) Prop up the appliance with the hose or dust contai-
ner handle.
b) Slide the hook on the floor nozzle into the storage
aid.
Disassembly
Fig. 18
•
To remove the flexible hose, press the two catches
together and pull out the hose from the appliance's
suction opening.
* Dependent on model