CNB A2363PL - Manual

OWNER'S MANUAL
COLOR ZOOM CAMERA SERIES
DIGITAL POWER ZOOM
Digital Zoom Camera Series
Day & Night Color Camera Day & Night Color Camera
230 x Digital Zoom
230 x Digital Zoom
3 COLOR VIDEO CAMERA 2 Digital Power Zoom
5 COLOR VIDEO CAMERA 4 Digital Power Zoom
7 COLOR VIDEO CAMERA 6 Digital Power Zoom
11 COLOR VIDEO CAMERA 10 Digital Power Zoom
13 COLOR VIDEO CAMERA 12 Digital Power Zoom
15 COLOR VIDEO CAMERA 14 Digital Power Zoom
19 COLOR VIDEO CAMERA 18 Digital Power Zoom
21 COLOR VIDEO CAMERA 20 Digital Power Zoom
23 COLOR VIDEO CAMERA 22 Digital Power Zoom
9 COLOR VIDEO CAMERA 8 Digital Power Zoom 17 COLOR VIDEO CAMERA 16 Digital Power Zoom
27 COLOR VIDEO CAMERA 26 Digital Power Zoom
29 COLOR VIDEO CAMERA 28 Digital Power Zoom
31 COLOR VIDEO CAMERA 30 Digital Power Zoom
25 COLOR VIDEO CAMERA 24 Digital Power Zoom
35 COLOR VIDEO CAMERA 34 Digital Power Zoom
37 COLOR VIDEO CAMERA 36 Digital Power Zoom
39 COLOR VIDEO CAMERA 38 Digital Power Zoom
33 COLOR VIDEO CAMERA 32 Digital Power Zoom
DSP DSP
MENU
T( )
W( )
( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
Class 2 Only
2. Connecting to Power
Each model has different power specification, please check the name of
the model and power specification before connecting to power source.
Please refer to the sticker identifying the model, which is attached on the
product, for power specification.
Resistance of copper wire [at 20℃ (68˚F)]
. As voltage may drop according to the length of electric cord as above
table, a camera may malfunction if too long output line of adaptor is
connected to the camera.
- Voltage for camera operation: 12VDC ± 10%
- Voltage drops on above table are variable according to types of electric cord
and makers.
Copper wire size (AWG)
Resistance(Ω/m)
#18 (0.83㎟)
Voltage Drop(V/m)
#24 (0.22㎟) #22 (0.33㎟) #20 (0.52㎟)
0.078 0.050 0.030 0.018
0.028 0.018 0.011 0.006
- The wire is polarized. Be careful of polarity.
- Use 12VDC power source.
DC 12V
Class 2 Only
For 12VDC Power Type
Receiver & Remote Control
1 2 3 4
Power
12VDC, 500mA
RS-485 Signal
- White Terminal :
- Black Terminal :
① Camera Selection - After camera connects with receiver, firstly check camera I.D.
② Menu (PROG): Shows / Hides Menu.
Moves up and down items. ③ (TELE):
④ (WIDE):
- Press camera I.D. number(1~39 buttons) on the top of wireless remote controller.
Caution : Usually camera I.D. number are selected from No.1 to No.39. over I.D. No.40, you will have a use limit.
- Initial camera I.D. number is set up No.0 when it takes out of manufacturer's warehouse.
Example: ZOOM IN I.D. No.5: Press 5 +<TELE> I.D. No.15: Press <F1>+ 5 +<TELE> I.D. No.24: Press <F2>+ 4 +<TELE> I.D. No.34: Press <F3>+ 4 +<TELE>
Set data for the selected items. ⑤ (NEAR):
⑥ (FAR):
④ ⑤
③ ⑥
②
①
F1
NEAR
FAR FOCUS
F3
WIDE
F2
TELE ZOOM AUTO
SEQ PAN
PROG
A
7
4
1
6
9
A 0
8
5
3 2
On-Screen Display
OSD OSD
MENU T( )
W( )
( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
Class 2 Only
MENU T( )
W( )
( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
AC 24V
Class 2 Only
DVR
Keyboard (Pelco-D)
• Serial Cable
• DVR -Connet to Serial PORT (COM1 or COM2)
TRxD +
TRxD - +
-
• Pelco-D Keyboard
• Camera RS-485 Converter
R
RS485
MENU
T( )
W( ) ( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
Class 2 Only
MENU
T( )
W( ) ( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
Class 2 Only
"C" Type Model : Remote control using for RS-232C.
PC (RS-232C)
Wired Remote Controller
Camera Terminal
KEY
KEY
Controller Wire
WHITE
BLACK
• Connecting to PC
NAME
1. Frame GND
2. RD
3. TD
4. DTR
5. Signal GND
6. DSR
7. RTS
8. CTS
9. RI
3
4
5
2
1
8
9
7
6 TD
RD
GND
• Serial Cable
• PC -Connet to Serial PORT (COM1 or COM2)
TD GND RD
R
KEY
MENU
T( )
W( )
( )N F( )
POWER
VIDEO OUT
DC 12V
RS485 UTP OUT UTP
2 VIDEO 1
AC 24V
Class 2 Only
① Function Setup Button
⑤ Power Input Terminal
④ Selection Switch
② Video Out Jack
③ Power LED
⑥ Control Terminal
⑦ UTP Video Output Terminal
UTP Transmisson Model "D" Type
② VIDEO OUT Jack: Used to connect an external video monitor in jack.
⑤ POWER Input Terminal
③ Power LED: The LED turns on when power is supplied.
⑥ Control Terminal
⑦ UTP Video Output Terminal: These terminals provide a composite
video output signal which may be transmitted over a twisted-pair connection to furnished with a suitable receiver.
① Function Setup Button: Functions can be setup using 5 buttons on the camera's rear panel.
MENU Buttons : Used to access menu mode. Also used to escape menu mode.
NEAR/FAR Buttons : Used to change the parameter of the selected menu item. It also moves the cursor the left of right in the menu screen.
TELE/WIDE Buttons : Used to choose the desired menu item. It also moves the cursor up or down in the menu screen.
MENU
T( )
W( )
( )N F( )
④ Selection Switch:
"D" Type • Used to choose video output or UTP output.
• When the distance is far from camera to monitor, set "Selection Switch" in 2 or 3. It shows more clear video on the monitor. "A&B&C" Type
MENU T( )
W( )
( )N F( )
POWER
VIDEO OUT
DC 12V
RS485 UTP OUT UTP 2 VIDEO 1
AC 24V Class 2 Only
Connect the UTP video output terminal on the back of the product to the monitor.
Camera
300m(Max)
UTP Cable
UTP Receiver
Monitor(or DVR)
UTP Video Output Model
• When using UTP video output terminal, set "Selection Switch"
at the "UTP OUT".
• When the distance is far from camera to monitor, set "Selection Switch"
in the middle.
The picture will show a better image.
• Connect UTP (Unshielded Twisted Pair) wire to the UTP output of the
camera directly.
UTP transmitter is included in the camera therefore additional UTP
transmitter is not necessary.
• UTP receiver is necessary to connect UTP wire to Monitor or DVR.
• When connecting UTP wire, make sure the polarity of the video signal.
• Use UTP wire "CAT5 24AWG" to have the best transmission quality.
Selection Switch fot Video Output
• Po we rf ul Zo om in g Fu
n c ti o n &
M
u lt i- In te r f ac e.
Auto Focus
" ND": No Display The OSDs of 1, 2, 3, 4, 5, 6, 8, 9, 11 disappear 5 sec later.
FUNCTION OSD EXPLANATION
4 White Balance
6 Shutter Speed
8 Motion Detect
9 Initial
LOGO
10 Zone Label
5 Pan / Tilt
7 ID
11 Zoom
ND
ND
ND
x125 ~ x10000
000 ~
255
x1 ...
Dx230
F.L
ND
MD
WAIT
-
Automatic color correction mode
Special color correction mode
Indoor mode
Outdoor mode
Temporary automatic mode
No Act Digital Panning / Tilting
Digital Panning / Tilting
Standard shutter speed (NTSC:1/60, PAL:1/50)
Flicker correction mode
Shutter speed indicator
Camera identification number
No motion detected
Motion detected
Displayed when POWER ON of the
camera is in operation
Explanation of the scene capture
by the camera (max. 10 letters)
Optical zoom: x1 ~ x23 Digital zoom: Dx24 ~ Dx230
* 'D' indicates digital zoom
SwB
IwB
OwB
PwB
Explanation of the On-Screen Display
The OSD (On Screen Display) is as follows:
X10000 255
WAIT
Dx230
1 2 3 4 5 6 7
9
8
Zone Label
11
MD
10
" ND": No Display
FUNCTION OSD EXPLANATION
1 Focus
2 Mirror
3 Backlight
ND
ND
ND
Automatic focus mode
Manual focus mode
No screen inverted
Screen is inverted to the left or right
Backlight compensation off
Backlight compensation mode
Automatic backlight compensation mode
7. On-Screen Display
Power On Function
MSG
BYTE 1
0xFF
BYTE 2
CamID BYTE 3
0x88
BYTE 4
0x00
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum Power Off Function
MSG BYTE 1 0xFF BYTE 2
CamID BYTE 3 0x08 BYTE 4 0x00 BYTE 5 0x00 BYTE 6 0x00 BYTE 7 Checksum
Pelco D Stop Function
MSG
BYTE 1
0xFF
BYTE 2
CamID BYTE 3
0x00
BYTE 4
0x00
BYTE 5 BYTE 6 BYTE 7
Checksum
Menu On / Off Function
MSG
BYTE 1
0xFF
BYTE 2
CamID BYTE 3
0x40
BYTE 4
0x00
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Focus Far Function
MSG
BYTE 1
0xFF
BYTE 2
CamID BYTE 3
0x00
BYTE 4
0x80
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Focus Near Function
MSG BYTE 1 0xFF BYTE 2
CamID BYTE 3 0x01 BYTE 4 0x00 BYTE 5 0x00 BYTE 6 0x00 BYTE 7 Checksum
Zoom Wide Function
MSG
BYTE 1
0xFF
BYTE 2
CamID BYTE 3
0x00
BYTE 4
0x40
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Zoom Tele Function
MSG
BYTE 1
0xFF
BYTE 2
CamID BYTE 3
0x00
BYTE 4
0x20
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
PELCO "D" Byte Format
Command Message
-RS-485,2400bps,1 Start bit,8 data bits,1 stop bit,no parity
Menu On / Off Function
MSG BYTE 1 0xFF BYTE 2
CamID BYTE 3 0x00 BYTE 4 0x23 BYTE 5 0x00 BYTE 6 0x5F BYTE 7 Checksum
Menu On / Off Function
MSG
BYTE 1
0xFF
BYTE 2
CamID BYTE 3
0x00
BYTE 4
0x03
BYTE 5
0x00
BYTE 6
0x62
BYTE 7
Checksum
Pelco Keyboard (95+ PATTERN)
V/D Keyboard (Set Preset + 98)
Don't care
6. Communication Protocol
MENU
T( )
W( ) ( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
Class 2 Only
MENU T( )
W( )
( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
AC 24V
Class 2 Only
Camera
Camera Intermediate Video Receiver End Equipment
Monitor
1. Connecting to Monitor
Connect the video out jack on the back of the product to the monitor.
• The method of connecting the camera to a monitor varies
depending on the model.
Please refer to the manual for your model.
• Connect the camera after switching off each piece of equipment.
• Change the 75Ω/Hi-Z conversion switch of each piece of equipment
according to the following diagram- move the switch of the
intermediate video receiver to Hi-Z, and the end equipment to 75Ω.
5. Installation . User Information
Model Description
Safety and Precautions
Features
Rear View and Part Names
Installation
Communication Protocol
On-Screen Display
Menu and Operation
Specifications
1.
2.
3.
4.
5.
6.
7.
8.
9.
5
6
7
8
10
18
19
21
39
40 .............
.............
. Contents
Avoid using the camera in extreme temperature environments.
Using the camera in temperatures exceeding 50˚C or below -5˚C may
lessen picture quality or cause the camera to malfunction.
Avoid using the camera in high humidity environments.
Using the camera in places with high humidity may lessen picture quality
because of moisture on the lens.
Avoid using the camera in unsteady lighting.
The camera will not work properly in places with great changes in
illumination intensity, such as fluorescent lamps.
Make sure no foreign substances get on the front glass of the camera.
Do not disassemble the camera and prevent foreign substances
from getting into the camera.
Make sure that the camera is not exposed to an intense light
source such as direct sunlight.
It may damage the CCD.
Camera may be damaged if dropped or subjected to strong impact.
Keep camera dry.
The camera will be damaged if immersed in water.
Avoid using the camera in the presence of oil and gas.
The camera will be damaged if oil or gas penetrates the exterior.
Caution
- Smear or blooming (when bright areas spreads out) may occur when
photographing in strong light, i.e. car headlights, etc. - Make sure that you are using a compatible power adapter before
connecting it to the camera.
2. Safety and Precautions
• Remote Control through RS-232C / RS-485 Interface
Remote control operations are possible through RS-232C / RS-485 interface for Focus and Zoom control. - In addition, the unit lets you command white balance and exposure manually using RS-232C / RS-485 interface.
• High Resolution
The horizontal resolution of 480/ 380 TV lines can be achieved by using a high density CCD having effective 410K/ 270K pixels,
which provides clean, noiseless and reliable pictures.
• PROTOCOL: Default, Pelco-D
• OSD(On-Screen Display) Function
• Wire Remote Controller (Option)
• Digital Slow Shutter for full color surveillance under very low light condition : 0.001Lux (at x 128 Field)
• Day & Night Function : 0.25Lux
• Coax or UTP(Unshielded Twisted Pair) Video Transmission.
Built-in UTP Transmitter provide a significant advantage in labor/ material saving on installations.
• AI / Fuzzy Control Circuit with DSP
Advanced DSP(Digital Signal Processor) technology automatically adjusts operations such as Iris, white balance flexibly adapting to
environmental conditions.
• Built-in Power Zoom Lens
Subjects can be magnified up to 230 times with be 23x optical zoom and 10x digital zoom.
UTP Video Out Model
Day & Night Model
3 . Features 9. Specficications
MENU
T( )
W( )
( )N F( )
CABLE DISTANCE
2 3 1
POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
AC 24V
Class 2 Only
MENU
T( )
W( )
( )N F( )
CABLE DISTANCE
2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
Class 2 Only
MENU
T( )
W( )
( )N F( )
CABLE DISTANCE
2 3 1
POWER
VIDEO OUT
DC 12V
Class 2 Only
TD GND RD
KEY RS232C
12VDC Input Model
① Function Setup Button
⑤ Power Input Terminal
④ Selection Switch
② Video Out Jack
③ Power LED
⑥ Control Terminal
① Function Setup Button
⑤ Power Input Terminal
④ Selection Switch
② Video Out Jack
③ Power LED
⑥ Control Terminal
① Function Setup Button
⑤ Power Input Terminal
④ Selection Switch
② Video Out Jack
③ Power LED
⑥ Control Terminal
24VAC/12VDC Input Model "B" Type
"A" Type
12VDC Input Model "C" Type
4. Rear View and Part Names
How to Set Up Functions
Functions can be setup using 5 buttons on the camera's rear panel.
MENU Key : Shows/Hides Menu
TELE/WIDE : Moves up and down items
NEAR/FAR : Set data for the selected item
1. Press the MENU button.
The Menu consists of the „Main Menu” and „Sub Menu”.
The main menu is displayed where 10 camera functions can be selected.
To the right of each main menu selection, the sub-menu is displayed.
(*) The above keys may be used differently
in some functions : 'Zone Label'
8. Menu and Operation
: This blinks to show that this category has been selected.
GENERAL
TELE
WIDE
NEAR FAR MENU
NEAR / FAR
TE LE / W ID E
MENU CAMERA ID
LANGUAGE
ZONE LABEL
BACKLIGHT
SHARPNESS
MIRROR
PROTOCOL GENERAL
FOCUS
AWB AE D&N SLOW_SHT
MOTION DISPLAY INITIAL EXIT
2. Press the TELE/WIDE button.
3. Press the NEAR/FAR button.
4. Press the OSD MENU button at the main menu or sub-menu screen to hide the menu.
It moves up and down the main menu category.
The sub-menu functions of the main menu category are displayed on the right.
It moves to the sub-menu window of the selected main menu.
The current set state of each sub-menu can be checked.
Press the TELE/WIDE button to move up and down the sub-menu category
and set each category by pressing the NEAR/FAR button.
It does not apply when the MENU button is used for other uses.
: 'Zone Label' setup screen
W ID E
MENU
FOCUS MODE
PUSH AUTO
FOCAL DIST
ZOOM START
ZOOM END
ZOOM SPEED
GENERAL
FOCUS
AWB
AE D&N
SLOW_SHT MOTION DISPLAY INITIAL
EXIT
TE LE / W
ID E
FOCUS
FOCUS MODE
PUSH AUTO
FOCAL DIST
ZOOM START
ZOOM END
ZOOM SPEED
INITIAL
EXIT Can be changed using the Near/Far button.
MANUAL
OFF
50CM
x001
x230
3
ON
Sets up the general operation of the camera.
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- GENERAL
1. CAMERA ID
Displays the camera's ID.
Camera ID can be specified using numbers from 000 to 255 by using
the NEAR/FAR button.
GENERAL
CAMERA ID LANGUAGE
ZONE LABEL BACKLIGHT SHARPNESS MIRROR
PROTOCOL INITIAL EXIT
Can be changed using the Near/Far button.
000 ENG
EDIT NORMAL 10 OFF
DEF ON
Move up and down using the TELE/WIDE button.
NEAR / FAR
N EA R / F AR
MENU
CAMERA ID
LANGUAGE
ZONE LABEL
BACKLIGHT
SHARPNESS
MIRROR
PROTOCOL GENERAL
FOCUS
AWB AE D&N
SLOW_SHT MOTION DISPLAY INITIAL
EXIT
- DEF (Default) - P/D (Pelco-D)
Edits and displays the information of camera or explanation on the area of the
image being captured at the bottom left of the screen.
Maximum of 10 letters can be used/ edited.
It is described in detail on page 39.
2. LANGUAGE
Displays the currently set language.
Language can be set from ENG to KOR and vice versa using the NEAR/FAR button.
3. ZONE LABEL
4. BACKLIGHT
5. SHARPNESS
6. MIRROR
7. PROTOCOL
8. INITIAL
9. EXIT
Use to select BLC mode.
BLC can be set from NORMAL, C1, C2, L1, L2, U1, U2, D1, D2, R1, R2 and
vice versa using the NEAR/FAR button.
Adjusts sharpness of outlines.
Can be set from 0 to 15.
P/D : Pelco-D
DEF : Default
Resets the current general settings category to the initial settings.
Inverts the screen to the right or left.
Closes the sub-menu and moves to the main menu.
Caution
Change the data of the sub-menu using the NEAR/FAR button.
MENU
FOCUS MODE
PUSH AUTO
FOCAL DIST
ZOOM START
ZOOM END
ZOOM SPEED GENERAL
FOCUS
AWB
AE
D&N SLOW_SHT MOTION DISPLAY
INITIAL EXIT
FOCUS
FOCUS MODE
PUSH AUTO
FOCAL DIST
ZOOM START
ZOOM END
ZOOM SPEED
INITIAL
EXIT MANUAL
OFF
50CM
x001
x230
3
ON
Note) Automatic focus in manual mode is only possible when the location of the zoom
lens has changed or when the "temporary automatic focus" category is selected.
Automatic focus is also possible based on external AF command (1 shot AF).
Sets camera zoom and focus.
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- FOCUS
1. FOCUS MODE
AUTO: Focuses automatically when the menu including D&N chages.
MANUAL: User focuses manually.
N EA R / F AR
Minimum distance the camera can focus.
ex) 10cm: Objects/subjects closer than 10cm cannot be brought into focus.
2. PUSH AUTO
When temporary automatic focus is selected, the camera focuses
automatically when only the NEAR/FAR button is pressed.
In the Automatic Mode, it will be displayed as "Not Used".
3. FOCAL DIST
4. ZOOM START
5. ZOOM END
6. ZOOM SPEED
8. EXIT
Minimum zoom movement.
Possible from x 001 to x 023
Maximum zoom movement.
Possible from x 001 to x 230
Closes the sub-menu and moves to the main menu.
Zoom speed movement. (Start x1 ~ End x23)
• 1 : 7 sec
• 2 : 5.5 sec
• 3 : 4 sec
7. INITIAL
Initializes the changed category in focus menu.
Adjusts picture color.
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- AWB
AWB
WB MODE
RED CONT
BLUE CONT
PUSH AUTO
INITIAL
EXIT AUTO
NOT USED
NOT USED
NOT USED
ON
N EA R / F AR
MENU
WB MODE
RED CONT
BLUE CONT
PUSH AUTO
GENERAL
FOCUS
AWB
AE D&N
SLOW_SHT MOTION DISPLAY INITIAL
EXIT
5. INITIAL
6. EXIT
Closes the sub-menu and moves to the main menu.
Initializes the changed category in AWB menu.
1. AWB
AUTO : Automatically adjusts color according to the available lighting.
PUSH AUTO : Color will be automatically adjusted while the NEAR/FAR button
is pressed in the temporary automatic mode.
OUTDOOR : Set color temperature to be 5400°K.
INDOOR : Set color temperature to be 3200°K.
SPECIAL : Color can be corrected when the user increases or decreases
"Red Control" or "Blue Control".
2. RED CONT
Can be changed in special mode only, and R-Gain value is adjusted.
Can be set from 0 to 255.
3. BLUE CONT
Can be changed in special mode only, and B-Gain value is adjusted.
Can be set from 0 to 255.
4. PUSH AUTO
Can chage WB Mode to PUSH AUTO.
Can be Push Auto whenever pushes NEAR/FAR button ('Off' is displayed to
'Push' whenever pushes key)
2. BRIGHTNESS
Brightness can be adjusted from 0 (dark) to 48 (bright).
Not used while in manual mode.
4. SHUTTER SPD
Can be changed while in manual and shutter manual mode.
Shutter speed can be changed from standard to 1/10000.
Standard shutter speed: NTSC- 1/60, PAL- 1/50.
5. IRIS ADJUST
Adjusts the opening of iris.
Can be adjusted from 0 (closed) to 255 (opened).
Change in screen can be recognized only within the certain range.
Can be adjusted while in manual and gain adjustment mode.
6. AGC ADJUST
Gain adjustment of image signal.
Can be adjusted from 0 to 255.
Can be adjusted while in manual and gain adjustment mode.
3. FLICKERLESS
Removes screen flickering caused by discordance of frequency and lighting.
7. AGC MAX SET
Maximum gain value used when gain is automatic.
Can be adjusted from 0 to 255.
8. INITIAL
Initializes the changed category in exposure menu to the initial settings.
9. EXIT
Closes the sub-menu and moves to the main menu.
Determines and operates in mode suitable for day or night.
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- D & N (option)
1. D&N MODE
AUTO : Filter operates automatically according to brightness.
NIGHT : Manual Mode- removes IR cut filter.
DAY : Manual Mode- does not remove IR cut filter.
2. D&N DELAY
Sets conversion time of IR cut filter while in automatic mode
Time can be adjusted from 1 to 10 seconds.
3. INITIAL
Initializes the changed category in night Day/Night menu.
4. EXIT
Closes the sub-menu and moves to the main menu.
N EA R / F AR
MENU
D&N MODE
D&N DELAY
GENERAL
FOCUS
AWB
AE D&N SLOW_SHT
MOTION DISPLAY INITIAL EXIT
D&N
D&N MODE
D&N DELAY
INITIAL
EXIT AUTO
10 SEC
ON
Use under very low light condition for full color surveillance.
OFF -> FLD2 -> --------------
è FLD128
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- SLOW_SHT (option)
1. SLOW_SHT
Use under very low light condition for full color surveillance.
OFF: Digital slow shutter function is disabled.
Can be adjusted from FLD 2 to FLD 128
2. INITIAL
Initializes the changed category in digital slow shutter menu.
3. EXIT
Closes the sub-menu and moves to the main menu.
N EA R / F AR
MENU
SHT_FLD
GENERAL FOCUS AWB
AE D&N
SLOW_SHT
MOTION
DISPLAY INITIAL EXIT
SLOW_SHT
SHT_FLD
INITIAL
EXIT FLD 24
ON
1. AE MODE
AUTO : Automatically adjusts brightness according to the available lighting.
MANUAL : Manually adjusts all brightness.
AGC MAN : Allows you to adjust gain.
IRIS MAN : Allows you to adjust iris.
SHUT MAN : Allows you to adjust the shutter speed.
Adjusts picture brightness.
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- AE
AE AE MODE BRIGHTNESS FLICKERLESS SHUTTER SPD
IRIS ADJUST AGC ADJUST AGC MAX SET INITIAL
EXIT
AUTO 26 OFF NOT USED
NOT USED NOT USED NOT USED ON
N EA R / F AR
MENU
AE MODE
BRIGHTNESS
FLICKERLESS
SHUTTER SPD
IRIS ADJUST
AGC ADJUST
AGC MAX SET
GENERAL
FOCUS
AWB
AE D&N SLOW_SHT
MOTION DISPLAY INITIAL EXIT
Note) Cannot adjust when D&N mode(refer to 31 page)is in Auto.
Note) There is a signal every time there is movement by the subject. If motion is
detected, MD (Motion Detected) is displayed on the upper left of the screen.
This message enables the user to set On-screen display state in the menu.
Note) The detection field on screen is as follows:
3. SENSITIVITY
Sets sensitivity to detect movement.
Can be set from 1 (low response) to 15 (sensitive).
4. INITIAL
Initializes the changed category in motion detection menu.
5. EXIT
Closes the sub-menu and moves to the main menu.
Caution
Error can occur in the motion detection function in the following cases.
(1) When lighting is unsteady.
(2) When light changes often even though there is no movement of the subject.
It is recommended that this function should be used after setting the
detection sensitivity and detection field after monitoring the environment for
an extended time.
CENTER
OUT
UPPER WHOLE
1. DETECT MODE
Enables or disables motion detection function.
2. DETECT AREA
Sets motion detection field.
Can be set to CENTER, OUT, UPPER and WHOLE.
When there is movement of the subject in the screen, there will be an
alarm, or the user will be informed through communications or "MD"
will display on the screen.
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- MOTION
MENU
N EA R / F AR
DETECT MODE
DETECT AREA
SENSITIVITY
GENERAL FOCUS AWB
AE D&N SLOW_SHT
MOTION
DISPLAY INITIAL
EXIT
MOTION
DETECT MODE
DETECT AREA
SENSITIVITY
INITIAL
EXIT OFF
CENTER
8
ON
Specity what to display on the screen.
Press the NEAR/FAR button to move to the sub-menu.
Main Menu- DISPLAY
DISPLAY WHOLE OSD FUNC OSD
MOTION DET CAMERA ID ZOOM MAG
ZONE LABEL VERSION INITIAL
EXIT
ON ON
ON ON ON
ON VER 1.0 ON
MENU
N EA R / F AR
WHOLE OSD
FUNC OSD
MOTION DET
CAMERA ID
ZOOM MAG
ZONE LABEL
VERSION
GENERAL
FOCUS AWB AE D&N
SLOW_SHT MOTION DISPLAY INITIAL
EXIT
1. WHOLE OSD
All on-screen display is "ON" or "OFF".
Nothing will be displayed if specified as "Hidden" even when other categories
are individually set as "ON". (Exception: Initial logo when power is turned on.)
Note) Refer to the "On-Screen Display" for details.
5. ZOOM MAG
Displays zoom on lower right of the screen.
The number in Dx230 shows the magnification, and D represents digital zoom.
2. FUNC OSD
Images displayed on the upper area of the screen.
Refer to the "On-Screen Display" section- images 1 to 6.
3. MOTION DET
"MD" is displayed on the upper left of the screen when motion is detected.
4. CAMERA ID
Displays ID number on the upper right of the screen.
6. ZONE LABEL
Displays texts explaining screen area on the lower left of the screen.
7. VERSION
Displays the version information of camera (cannot be changed).
8. INITIAL
Initializes the changed category in on-screen display menu.
9. EXIT
Closes the sub-menu and moves to the main menu.
Caution
Please use caution when performing this function.
Every setting(even in all sub-menus)will be initialized.
Initialization in sub-menus will initialize each category of the sub-menu only.
Initializes all current settings.
No sub-menu.
Press the NEAR/FAR button to initialize the entire camera settings.
Note that all settings in the sub-menus will be initialized.
OFF STATE : Indicates that settings are not initialized.
ON STATE : Indicates that camera settings have been initialized.
Main Menu- INITIAL
MENU
MENU
N EA R / F AR
OFF STATE
ON STATE
GENERAL
FOCUS AWB AE D&N
SLOW_SHT MOTION DISPLAY INITIAL
EXIT
GENERAL FOCUS AWB
AE D&N SLOW_SHT MOTION
DISPLAY INITIAL EXIT
Closes menu. Press the NEAR/FAR button to close menu.
Main Menu- EXIT
MENU GENERAL FOCUS AWB AE D&N SLOW_SHT MOTION DISPLAY INITIAL EXIT
1. You can choose up to 84 symbols from the available symbols table.
2. Select the location of letters using the TELE/WIDE button. A downward arrow will blink on top of the letter to edit.
3. Select letters using the NEAR/FAR button. 4. To exit, press the MENU.
ZONE LABEL
FRONT DOOR
TE/WI - POSITION NE/FA - CHAR SELECT MENU - EXIT
Max. 10 Letter
User can edit explanation or condition of camera, and this will be
displayed on the lower left screen.
ZONE LABEL
NU + o X
G
¢ з и И З % & ) ( _ . “ ? ; : / - * # ! ~ z y x w v u t s r q p n m l k j i h g f e d c b a Z Y W V U T S R Q P O N M L K J I H
F E D C B A 9 8 7 6 5 4 3 2 1 0
: Space
Caution) : denotes a blank letter and will be displayed as a blank space on the actual screen.
È
Before operating the camera, confirm the camera model and proper
power voltage. In order to understand the manual thoroughly,
we'll introduce our model descriptions.
Thank you for purchasing this COLOR ZOOM CAMERA.
Type (Rear) Signal System Model No.
NTSC/High
PAL/High
NTSC/High
PAL/High
NTSC/High
PAL/High
NTSC/High
PAL/High
1
2
3
4
5
6
7
8
D&N DSS Communication System
O
O
O
O
O
O
O
O
RS-485/PTZ Controller
RS-485/PTZ Controller
RS-232C
RS-232C
RS-485/PTZ Controller
RS-485/PTZ Controller
RS-485
RS-485
X
X
X
X
X
X
O
O
UTP Output
12VDC
12VDC
12VDC
12VDC
24VAC/12VDC
24VAC/12VDC
24VAC/12VDC
24VAC/12VDC
Power Input
A
A
C
C
B
B
D
D
1. Model Description
Design and specifications are
subject to change without notice.
MENU T( )
W( )
( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
AC 24V
Class 2 Only
3. Camera Control Methods
"A" & "B" Type Model : Remote control using for PTZ controller.
"A" & "B" & "D" Type Model : Remote control using for RS-485.
• PTZ Controller
Z
F
C
• Receiver & Remote Control • Pelco-D Keyboard
• DVR System
• Signal (RS-485)
MENU
T( )
W( )
( )N F( )
POWER
VIDEO OUT
DC 12V
RS485 UTP OUT UTP
2 VIDEO 1
AC 24V
Class 2 Only
MENU
T( )
W( )
( )N F( ) CABLE DISTANCE 2 3 1 POWER
VIDEO OUT
F C Z
RS485 CONTROLLER
DC 12V
AC 24V
Class 2 Only
• When using 24VAC power with UTP wire, it is possible to supply the power within 100m.
• Use 4 wires by 2 pair of wires. • When using 12VDC power, UTP wire can not be used for power line.
For 24VAC / 12VDC Power Type
For 24VAC / 12VDC Power Type [UTP Video Output]
. Be sure to connect power after all the installation is done. . Note that AC adaptor is not supplied with camera.
. Use only 24VAC / 12VDC UL listed class 2 power supply. . Do not use power sources other than that specified.
Notes
- Use 24VAC power source or 12VDC power source.
DC 12V
AC 24V
AC 24V
Power Supply
100m(Max)
2 Wire
PAL NTSC Signal System
Scanning System
Horizontal Scanning Frequency
Vertical Scanning Frequency
Image Sensor
Total Pixels
Effective Pixels
Horizontal Resolution
S/N Ratio
Lens
Angle of View (HOR)
Minimum Illumination
Synchronization
Signal Output
Power Consumption
(Option: AC24V/DC12V)
Dimensions (WxHxD)
Weight
2 : 1 Interlace
15.734 kHz 15.625kHz
59.94 Hz 50 Hz
1/4 Inch SONY Super HAD CCD
537(H) x 505(V) 270K 537(H) x 597(V) 320K
510(H) x 492(V) 250K 500(H) x 582(V) 290K
More than 380 TV lines
More than 48dB (AGC off)
23x Zoom Video AF
(F1.6(W), F3.3(T) f=3.6~83.4mm)
55.21˚ ~ 2.44˚
Day Mode: 0.6 Lux(30 IRE) /
Night Mode: 0.1 Lux(30 IRE)
Internal
1Vp-p Composite Output with 75Ω Terminated
12VDC (9V~15V), Max. 4.56W / 380mA
24VAC (20V~28V) or 12VDC (10V~15V), Max 6W/ 0.5A
65 x 62 x 122mm, 5 x 62 x 140mm [Long Body]
Approx 325g, 370g [Long Body]
P /N :3 8 1 0 -0 1 4 3 A
ve r. 0 8 0 2 E
9. Specficications
PAL NTSC Signal System
Scanning System
Horizontal Scanning Frequency
Vertical Scanning Frequency
Image Sensor
Total Pixels
Effective Pixels
Horizontal Resolution
S/N Ratio
Lens
Angle of View (HOR)
Minimum Illumination
Synchronization
Signal Output
Power Consumption
(Option: 24VAC/12VDC)
Dimensions (WxHxD)
Weight
2 : 1 Interlace
15.734 kHz 15.625kHz
59.94 Hz 50 Hz
1/4 Inch SONY Super HAD CCD / EX-View CCD
811(H) x 508(V) 410K 795(H) x 596(V) 470K
768(H) x 494(V) 380K 752(H) x 582(V) 440K
More than 480 TV lines
More than 48dB (AGC off)
23x Zoom Video AF
(F1.6(W), F3.3(T) f = 3.6~83.4mm)
55.21˚ ~ 2.44˚
Day Mode: 0.6 Lux(30 IRE) / Night Mode: 0.1 Lux(30 IRE)
DSS (128FLD) Mode: 0.001 Lux (30 IRE)
Internal
1Vp-p Composite Output with 75Ω Terminated
12VDC (9V~15V), Max. 4.56W / 380mA
24VAC (20V~28V) or 12VDC (10V~15V), Max 6W/ 0.5A
65 x 62 x 122mm, 65 x 62 x 140mm [Long Body]
Approx 325g, 370g [Long Body]
High Resolution
Normal Resolution
Do not insert the POWER cable
WARNING!
Do not insert the POWER cable
WARNING!
Do not insert the POWER cable
WARNING!
Normal Resolution
High Resolution
Explanation of two Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of un-insulated
"dangerous voltage" within the product's
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and
maintenance-(servicing) instructions in the
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE
ON THE BOTTOM OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THE UNIT TO RAIN OR MOISTURE"
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
literature accompanying the appliance.
INFORMATION
This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the
equipment.
CAUTION - To prevent electric shock and risk of fire hazards:
Do NOT use power sources except for that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person
and should abide to all local codes.
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN