CNB D2315PVFTP - Manual

camera color
1/3" SONY CCD
Design and specifications are
subject to change without notice.
Dome Camera Color Dome
Vandal Proof Digital DSP
LENS .Vari-focal
.Fixed Lens
3-Axis
• S
im
p l e
t o i n s t a l l 3 -
A
x i s
b
r a
c k e
t
m ak
es
ad ju st m en
t
e a s y
.
CAUTION : In case of AGC off,
the switching of D&N doesn't work.
Because the D&N switching function
is related in AGC level.
Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
a
DC Level Adjustment V.R
Function Selection Switch:
•FL(Flickerless) ON/OFF
•AGC(Auto Gain Control) ON/OFF
•BLC(Back Light Compensation)
ON/OFF
b
c
SPECIFICATIONS:
COMPOSITION:
Model
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
BLC
Flickerless
Input / Output Connector
Power Consumption
Dome Size (Ø)
Weight
NTSC PAL
NTSC : 525 Lines PAL : 625 Lines
2 : 1 Interlace
15.734kHz 15.625kHz
59.94Hz 50Hz
1/3 inch SONY IT CCD
410K/380K [Normal:270K/250K] 470K/440K[Normal:320K/290K]
More than 48dB (AGC Off)
550 TV Lines [High: 480 TV Lines / Normal: 380 TV Lines]
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=2.45mm, 3.8mm, 6mm Selectable)/ Vari-focal Lens
Manual
Internal
0.3 Lux(High/Normal)/ 0.1 Lux(Day&Night)/ 0 Lux(IR LED)
1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec.
Auto
On / Off (with Slide Switch)
On / Off (with Slide Switch)
On / Off (with Slide Switch)
Power, Video, UTP (Option)
AC 24V (20V~28V) or DC 12V (10V~15V), 5W (Max)
100mm
Approx. 366g / 844g / 1210g
You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.
Built-in camera
bracket will make user
much easier to rotate in
any direction.
3-axis NAME AND FUNCTION:
Vari-focal Lens Type
CAMERA SET-UP:
The image does not
appear on the screen.
Check the power source for the monitor and camera
and assure that the voltage and polarity are properly
connected and being supplied correctly.
The image on the
screen is dim.
Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.
Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our After Service department.
The screen blinks a lot. Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
4
5
2
1
3
Owner's Manual
Guide Pattern Service Monitor Cable
L-Wrench
No.
#1
#2 Function
Video Output
Power Input
R e m a r k
1.0 Vp-p
AC24V(20V~28V)orDC12V(11V~15V), Max 5W/420mA
Terminal Color
Yellow
Green
#1
#2
Video
(Yellow)
Power- AC 24V/ DC 12V
(Green)
Video Output
GND
Surface Mount Bracket
Tapping Screw
Surface Mount Screw
! Do not install the camera in
extreme temperature conditions.
Do use the camera under conditions where
temperatures are within -10°C to 45°C.
Be especially careful with ventilation
under high temperatures.
! Do not install or use the camera
in an environment where the
humidity is high.
It can cause the image quality to be poor.
! Do not drop the camera or
subject them to physical shocks.
It can cause malfunctions to occur.
! Do not disassemble the camera.
There are no user-serviceable parts
inside it.
! Note
When this camera is installed near
wireless communication devices
that emits strong electromagnetic
field, irregularity such as noise on
the monitor may appear.
PRECAUTIONS:
CONNECTION:
Connecting to Monitor and Power
• The wire is non-polarized.
• Use AC 24V power source or
DC 12V power source.
AC 24V/DC 12V Power Type
Camera Lay-out
Tilt rotation: Adjusting the vertical angle.
Pan rotation: Adjusting the horizontal angle.
Horizontal rotation: Adjusting the horizontal
position of the screen.
Focus handle: Focus (Far or Near)
Zoom handle: Zoom (Tele or Wide)
1
2
3
4
5
UTP (Unshielded Twisted Pair) : Option
HEATER: Option
Connecting to Power
Connecting to Monitor
• When using AC 24V power, it is possible to supply the
power within 100m.
• Use 4 wires by 2 pair of wires.
• When using DC 12V power, UTP wire can not be used
for power line.
• Connect UTP (Unshielded Twisted Pair) wire to the UTP
output of the camera directly.
UTP transmitter is included in the camera therefore
additional UTP transmitter is not necessary.
• UTP receiver is necessary to connect UTP wire to
Monitor or DVR.
• When connecting UTP wire, make sure the polarity of
the video signal.
• Use UTP wire "CAT5 24AWG" to have the best transmission
quality.
• The twisted-pair output cannot be used at the same
time as the composite video output.
• Power Consumption: 10W
• Operating Temperature Range: -40°C ~ 50°C
Monitor(or DVR)
300m(Max)
UTP Cable
UTP Receiver
AC 24V
Power Supply
100m(Max)
2 Wire
P
/N
:3
8
1 0 -0
0
9 4 A
ve
r.
0 6 0 8 E
360º
360º
90º
IR LED (3.8mm Fixed Lens Only) : Option
• Power Consumption: 5W
• IR LED Specification: 850nm / 30° (24EA)
Owner's Manual
Guide Pattern Service Monitor Cable
Mounting Screw
L-Wrench
Owner's Manual
Guide Pattern
Service Monitor Cable
Mounting Screw
Simple to install
3-Axis bracket makes
adjustment easy.
The 3D bracket (Pan, Tilt and Horizontal)
allows the camera to be manually as well
as moved horizontally and vertically.
HE AT ER
J5 05
J5 03
VIDEO J5 07 SW
50 1
VR 50 1
ON 3
1
2 3
1 2
DC L EV EL T1 02
UT P M OD UL
E
BLC
AGC
FL
OFF ON
OFF
ON OFF
ON
J5 01
BL C
AG C FL
OF F ON OF F
ON OF F ON
3 12
a c
b
General Dome Camera
Vandal Resistant Dome Camera (Surface Type)
Vandal Resistant Dome Camera (Flush Type)