Alliance Laundry Systems SFGX09*F - Manual (Page 26)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Installation
510977 24
8. Using screwdriver, remove two door plugs, and
reinstall on opposite side of door opening.
9. Reinstall four hinge attaching screws, removed in
Step 1.
Step 6: Wipe Out Inside of Dryer
Before using dryer for the first time, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside dryer drum.
Figure 31
Step 7: Plug In the Dryer
Electric Dryer
Connect the dryer to an electrical power source. Refer
to Step 4 for information on connecting power cord.
Figure 32
Gas Dryer
Dryer requires 120 Volt, 60 Hertz electrical supply and
comes equipped with a 3-prong grounding plug. Refer
to serial plate for specific electrical requirements.
NOTE: The wiring diagram is located inside the
control hood.
When plugging in the dryer:
● Do not overload circuits.
● Do not use an adapter.
● Do not use an extension cord.
● Do not operate both a washer and gas dryer on
the same circuit. Use separately fused 15 Amp
circuits.
Figure 29
Figure 30
D621I
IN U SE
PE RM P RE SS
NO RM AL
FL UF F (N O HE AT ) DE LIC AT E
PU SH TO S TA RT
FA BR IC S EL EC TO R
50 42 10
OP ER AT IN G INS TR UC TIO NS
CL EA N LIN T F ILT ER A FT ER E AC H L OA D
1.
2. 3. 4. 5. 6.
Se lec t F abri c T ype (h eat se ttin g)
N OR MA L, P ER M P RE SS ,
DE LIC AT E, F LU FF (n o h eat )
Loa d C loth es.
Ins ert Co in(s )/C ard .
To St art Dry er - C los e D oor an d P ush Sta rt.
To Sto p D rye r D urin g C ycl e - Op en D oor.
To Re sta rt D rye r - C los e D oor an d P ush Sta rt.
Dry ing Cy cle is C om ple te W hen
Pa nel Lig ht G oes Off.
D385i
D385I
D606I D606I
IN U SE
PE RM P RE SS
NO RM AL FL UF F (N O HE AT ) DE LIC AT E
PU SH TO S TA RT
FA BR IC S EL EC TO R
504210
OPERATING INSTRUCTIONS
CL EA N LIN T F ILT ER A FT ER E AC H LO AD
1.
2. 3. 4. 5. 6.
Se lec t F abr ic T ype (h eat se ttin g)
N OR MA L, P ER M P RE SS ,
D EL ICA TE , F LU FF (n o h eat )
Loa d C loth es.
Ins ert Co in(s )/C ard .
To St art Dr yer - C los e D oor an d P ush St art .
To St op Dry er Du ring Cy cle - O pen Do or.
To Re sta rt D rye r - Clo se Do or and Pu sh Sta rt.
Dry ing Cy cle is Co mp lete W hen
Pa nel Lig ht G oes Of f.
D621I
D275I
Connect to 30 Amp circuit.
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST conform with the latest
edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local
regulations as might apply. It is the
customer’s responsibility to have the wiring
and fuses installed by a qualified electrician
to make sure adequate electrical power is
available to the dryer.
W521
WARNING