DRIVEN DSBLOCK 1,2,3,4,5,6,8 User Manual
DRIVEN For motorcycles
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11
.
Make sure ignition key is turned to the of
f position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
Locate the final destination of the new block of
f plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
Using blue Loctite, install the new block of
f plates using the OEM hardware,
and the OEM sealing “O rings” if present.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
DRIVEN REQUIRES THIS PRODUCT T
O BE INST
ALLED BY
A
CERTIFIED TECHNICIAN
NOT INTENDED FOR STREET/HIGHW
AY
USE! FOR OFF ROAD/RACE USE ONL
Y!
DRIVEN PERF
ORMANCE PR
ODUC
T
S
W
W
W
.DRIVENRA
C
ING.
COM
866-5-DRIVEN
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 1
1, 13, 15)
(Installation Instructions)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11
.
Make sure ignition key is turned to the of
f position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
Locate the final destination of the new block of
f plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
Using blue Loctite, install the new block of
f plates using the OEM hardware,
and the OEM sealing “O rings” if present.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
DRIVEN REQUIRES THIS PRODUCT T
O BE INST
ALLED BY
A
CERTIFIED TECHNICIAN
NOT INTENDED FOR STREET/HIGHW
AY
USE! FOR OFF ROAD/RACE USE ONL
Y!
DRIVEN PERF
ORMANCE PR
ODUC
T
S
W
W
W
.DRIVENRA
C
ING.
COM
866-5-DRIVEN
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 1
1, 13, 15)
(Installation Instructions)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11
.
Make sure ignition key is turned to the of
f position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
Locate the final destination of the new block of
f plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
Using blue Loctite, install the new block of
f plates using the OEM hardware,
and the OEM sealing “O rings” if present.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
DRIVEN REQUIRES THIS PRODUCT T
O BE INST
ALLED BY
A
CERTIFIED TECHNICIAN
NOT INTENDED FOR STREET/HIGHW
AY
USE! FOR OFF ROAD/RACE USE ONL
Y!
DRIVEN PERF
ORMANCE PR
ODUC
T
S
W
W
W
.DRIVENRA
C
ING.
COM
866-5-DRIVEN
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 1
1, 13, 15)
(Installation Instructions)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11
.
Make sure ignition key is turned to the of
f position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
Locate the final destination of the new block of
f plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
Using blue Loctite, install the new block of
f plates using the OEM hardware,
and the OEM sealing “O rings” if present.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
DRIVEN REQUIRES THIS PRODUCT T
O BE INST
ALLED BY
A
CERTIFIED TECHNICIAN
NOT INTENDED FOR STREET/HIGHW
AY
USE! FOR OFF ROAD/RACE USE ONL
Y!
DRIVEN PERF
ORMANCE PR
ODUC
T
S
W
W
W
.DRIVENRA
C
ING.
COM
866-5-DRIVEN
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 1
1, 13, 15)
(Installation Instructions)