beautypg.com

BARSKA AX11650 - Large Biometric Safe User Manual

Page 2

background image

BEEP SOUND OPTIONS

Beep OFF: Press and HOLD the Initialization Button (A) (20 -

30 seconds) until the Indicator Lights (E) flash green once

- RELEASE the Initialization Button

Beep ON: Press and HOLD the Initialization Button (A) (20 -

30 seconds) until the Indicator Lights (E) flash green, followed

by 1 beep

- RELEASE the Initialization Button

OPEN SAFE WITH EMERGENCY KEY

1. To expose the Emergency Key access, remove Logo

Plate (G) screws with provided tool

2. Insert Emergency Key into key access, push and turn key

counter-clockwise, and turn Handle (H) clockwise to open

the safe

NOTE: Store Emergency Keys in a secure place, NOT inside

of the safe

OPEN SAFE WITH EXTERNAL BATTERY PACK

Use this option when internal batteries are low

1. Insert 4 AA batteries into External Battery Pack (I)

2. Plug into External Battery Access (J)

3. Press and release Wake-Up Button (F)

- Place a registered finger on Fingerprint Scanner (D)

- Turn Handle (H) clockwise to open the safe

DELETE ALL STORED FINGERPRINTS / RESET TO

FACTORY DEFAULT MODE

1. Open safe, remove Battery Compartment (B) cover and

all 4 AA batteries

2. Press and release Wake-Up Button (F) a few times until no

beeps are heard

3. Press and HOLD the Initialization Button (A)

- Re-insert batteries; on the 4th battery you will hear 1

beep, followed by 2 consecutive beeps indicating safe is

in Factory Default mode

4. RELEASE Initialization Button (A)

5. Repeat steps 1-3 if a total of 3 beeps are not heard

6. Restore Battery Compartment (B) cover

7. All fingerprints stored in the safe have been deleted

NOTE: The safe is in Factory Default mode, ANY fingerprint

can open the safe

8. Continue with FINGERPRINT REGISTRATION and TEST

(NON) REGISTERED FINGERPRINTS

LOW BATTERY WARNING

1. When the door is closed and 3 repetitive beeps are heard,

and Indicator Lights (E) flash red, it indicates the batteries

are low

2. Replace batteries immediately

- Open safe, remove Battery Compartment (B) cover and

all 4 AA batteries

- Insert 4 new AA batteries and restore Battery

Compartment (B) cover

NOTE: All registered fingerprints remain stored

CARE AND MAINTENANCE

- To maximize the security and performance of the safe, keep

Fingerprint Scanner (D) clean; use a dry cloth to remove

any smudges or prints off the Fingerprint Scanner after

each use

- Test registered fingerprints every 6 months

- Keep liquids away from the control panel. Spills on the

control panel will cause damage and possibly electric shock

- Secure safe in a proper area to prevent from falling and

causing damage or injury

- DO NOT disassemble the product. For all repairs, contact

BARSKA Customer Service

- DO NOT use chemicals or cleaning agents to clean the safe

MOUNTING INSTRUCTIONS

The safe must be mounted to a wall or floor. Be aware of the

load bearing. Failure to do so can result in personal injury and/or

damage to property. Use appropriate

tools when performing work and always

use eye protection

Wall Mounting

Do not mount the safe without anchoring

to the wall

- Find the studs in the wall, at your

desired location. Most studs

are 16 inches or 24 inches apart

- Check the wall for concealed wires

or pipes

Mounting Holes

* Actual model may vary

- Measure the location of the pre-set drill holes; mark their exact

position onto the wall ensuring that the studs or anything else

behind will not interfere

- Drill the appropriate size holes for the anchors you are using

- Carefully press the anchor into the holes at this time

- Mount the safe by running screws from inside of the safe

and securing to anchors; ensure the safe is mounted securely

Floor Mounting

- Use proper drill tools depending on the type of floor you are

mounting the safe (wood, tile, or concrete)

- Measure the location of the pre-set drill holes; mark their

exact position onto the floor

- Drill the appropriate size holes for the anchors you are using

- Carefully press the anchor into the holes at this time

- Mount the safe by running screws from inside of the safe

and securing to anchors; ensure the safe is mounted securely

This manual is related to the following products: