Xylem F450 VARIABLE AREA INLINE FLOWMETERS - Manual

® Your Blue-White F-450 Series
® !Your Blue-White flowmeter was designed to be
easy to install.
!Please read the Instruction Guideline on the next
page before installing your flowmeter.
!This flowmeter is an instrument, special care
should be taken when handling and installing.
Inspection of the Flowmeter and Compatibility
!Carefully inspect the meter for any damage that may have occurred during shipping.
!Remove the plastic tubing that has been inserted during packaging for shipping
reasons.
!Make sure your pressure, temperature, fluid and other requirements are compatible
with the meter before installation.
!The maximum temperature capability decreases as the pressure increases. The max
PSI decreases as the temperature increases. See the chart on the following page.
® !Although the meter may be suitable for other chemicals, Blue-White meters are tested
with water. If you are unsure of the meters compatibility with your chemical, please
consult the factory.
® !Blue-White warranties the flowmeter for use with air and water only.
Installation Instructions
80000-060 10/15/2003
F-450
Blue-White
Industries, Ltd.
R
Model No.
F-45330
F-45375
F-45376
F-45500
F-45750
F-45330E
F-45375E
F-45376E
F-45500E
F-45750E
F-45330EA
F-45375EA
F-45376EA
F-45500EA
F-45750EA
Dim A
8-7/8”
225.5mm
8-7/8”
225.5mm
8-7/8”
225.5mm
8-7/8”
225.5mm
10”
254mm
Dim B
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
Dim C
NA
Dim D
9-7/8”
250.8mm
9-7/8”
250.8mm
9-7/8”
250.8mm
9-7/8”
250.8mm
10”
254mm
3-1/8”
79.4mm
3-1/8”
79.4mm
3-1/8”
79.4mm
3-1/8”
79.4mm
3-1/8”
79.4mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
8-9/16”
217.5mm
8-9/16”
217.5mm
8-9/16”
217.5mm
8-9/16”
217.5mm
9”
228.6mm
NA
NA
NA
NA
NA
NA
NA
NA
NA
9-7/8”
250.8mm
9-7/8”
250.8mm
9-7/8”
250.8mm
9-7/8”
250.8mm
10”
254mm
4”
101.6mm
4”
101.6mm
4”
101.6mm
4”
101.6mm
4”
101.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
1-7/8”
47.6mm
8-9/16”
217.5mm
8-9/16”
217.5mm
8-9/16”
217.5mm
8-9/16”
217.5mm
9-1/8”
231.8mm
A
D
B
C
A D
C
B
A
B
BLUE-WHITE INDUSTRIES LIMITED WARRANTY
FLOWMETERS are warranted to be free of defects in material and workmanship
for up to 12 months from the date of factory shipment. Warranty coverage is
limited to repair or replacement of the defective flowmeter only. Blue-White
Industries does not assume responsibility for any other damage that may occur.
This warranty does not cover damage to the flowmeter that results from misuse
or alterations, nor damage that occurs as a result of: meter misalignment,
improper installation, over tightening, use of non- recommended chemicals, use
of non-reccomended adhesives or pipe dopes, excessive heat or pressure, or
allowing the meter to support the weight of related piping. Flowmeters are tested
and calibrated with water and air only. Although meters may be suitable for other
chemicals, Blue-White cannot guarantee their suitability.
Flowmeters are repaired at the factory only. Call or write the factory to receive a
Return Authorization Number, carefully pack the flowmeter to be returned,
including a brief description of the problem. Note the RA number on the outside
of the carton.
Website: www.Blue-White.com
E-mail: [email protected] | [email protected]
Phone: 714-893-8529 | Fax: 714-894-9492
5300 Business Drive
Huntington Beach, CA 92649
Blue-White
Industries, Ltd.
R
F-450 F-450E
F-450EA
Meter Body: Polysulfone
Float: 316SS, Hastelloy C-276, PVC, or Teflon
(based on model)
Guide rod: # 316 Stainless (opt. Hastelloy C-276)
Adapters: Polysulfone
O-Rings: Viton
Scale: Permanent, dual scale silkscreen (black ink)
Max. PSIg: 150 PSIG / 10.3 BAR at 70 F/21 C
Max. Temp: 212
°F / 100°C at 0 pressure
Accuracy: ± 5% of full scale reading
° °