Procom X-Mount - Manual

X-Mount
Stream-lined Mobile Mount
DESCRIPTION
Mobile mount with a nice, “streamline”-look, which can be installed
everywhere on the car in an 18 mm dia. hole.
Especially suited for mounting on the narrow strip on rear wing between
trunk lid and car side.
M6 thread whip-mounting system.
Very low requirements to installation depth both under and after
installation.
Designed for installation with access from the outside only.
With access available from the inside, installation is possible in a 14 mm
dia. hole.
Bendable section in mount makes whip tiltable 30° by hand.
Complete line of whips available for all communications bands up to
1300 MHz.
Mounting body made of stainless steel !
Choice between two connection principles:
X-mount: FME-connection (supplied without cable).
XP4-mount: Permanently attached 4 m cable terminated with FME-
connector.
ORDERING DESIGNATIONS
TYPE NO. PRODUCT NO.
X-Mount X-mount with FME-system
XP4-Mount XP4-mount with 4m cable and FME-connector
SPECIFICATIONS
MODEL X-MOUNT
APPLICATION Mount for mobile antennas
FREQUENCY 0 - 1300 MHz
CONNECTION TO WHIP M6 thread stud
MATERIALS Stainless steel
Black chromed brass
Cu-nite brass
Environment-proof plastics
COLOUR Black
HEIGHT Approx. 42 mm
LENGTH/WIDTH 41. 5 mm/27.5 mm
BUILD-IN DEPTH Active : 30 mm
Passive : 11 mm
RECOMMENDED
INSTALLATION TORQUE
4 ± 1 Nm
WEIGHT X-version : Approx. 40 g
XP4-version : Approx. 180 g
MOUNTING 18 mm dia. hole
ROOF THICKNESS Max. 2 mm
FME-SYSTEM ACCESSORIES
FME-CABLES
LENGTH TYPE NO.
1 m 1 m FME
2 m 2 m FME
3 m 3 m FME
4 m 4 m FME
5 m 5 m FME
6 m 6 m FME
4 m white 4 m FME-white
6 m white 6 m FME-white
12 m white 12 m FME-white
18 m white 18 m FME-white
FME-CONNECTORS
CONNECTOR ORDER NO.
FME-FME FME-FME
Prolongation FMEP
N FME-N
FSMA FME-FSMA
BNC FME-BNC
TNC FME.TNC
UHF FME-UHF
Mini-UHF FME-MUHF
Elbow-MUHF FME-EMUHF
Elbow-BNC FME-EBNC
Elbow-TNC FME-ETNC
SMA FME-SMA
For further information about other types of FME-cables please compare the cable data sheets under
accessories in our catalogue.
INSTALLATION
X-mount antenna types can be mounted anywhere on the car, however, roof
top mounting is always recommended.
The X-mount is able to be mounted on the often very narrow strip on the
rear wing between the trunk lid and the side of the car.
Mounting can take place exclusively with access from the outside when
drilling an 18 mm dia. hole. Mounting can take place from the inside by
drilling a 14 mm dia. hole, in which case the bottom plastic ring of the
packing gasket should be removed with a sharp cutter.
A good contact surface on the inside of the car body must always be
ensured, thus enabling the base plate to get in direct contact with the metal
parts of the car, which is of utmost importance for proper performance of
the antenna.
When cleaning the car in car-washing machines, the whip is easily removed
using a fork spanner. The whip is refitted again by screwing it onto the
thread stud and tightening it lightly with the spanner.
As the X-mount is internally equipped with a bendable section, the antennas
can always be adjusted to an upright position independent of the tilt angle
of the installation spot (up to 30° tilt).
1. INSTALLATION DIMENSIONS