Procom DPF 2-6-sht-... User Manual
Dpf 2/6-sht

DPF 2/6-SHT-...
6-Cavity Duplexer for the 175 - 250 MHz Band
DESCRIPTION
The DPF 2/6-SHT-… is a 6-cavity duplex filter for duplex
radiotelephones.
This duplexer is delivered in a low band version type
DPF 2/6-SHT- L, tunable within 175 - 250 MHz, medium band version
type DPF 2/6-SHT-M, tunable within 200 - 230 MHz and a high band
version type DPF 2/6-SHT-H, tunable within 230 - 260 MHz. These
models are again delivered in 3 submodels, each dedicated to work with
a certain duplex spacing.
See “Ordering information” below.
The DPF 2/6-SHT-… models are primarily intended for equipment, where
the TX and RX operate on single frequencies, but they can also,
however with slightly reduced data, be used where the TX and RX
operate on several channels, i.e. within a certain port bandwidth. In the
last case, factory tuning is recommended.
The filter has very small physical dimensions owing to the use of high-Q,
temperature compensated helical resonators.
The housing is made of extruded aluminium, the chassis of passivated
steel, and teflon insulation has been applied in the rigid coaxial cables
and in the connectors.
The filter is black vinyl coated to prevent corrosion.
ORDERING DESIGNATIONS
TYPE NO.
PRODUCT NO.
TUNING RANGE
(MHZ)
DUPLEX SPACING
(MHZ)
DPF 2/6-SHT-L-4/6
200001852
175 - 200
4 - 6
DPF 2/6-SHT-L-6/8
200001853
6 - 8
DPF 2/6-SHT-L-8/10
200001854
8 -10
DPF 2/6-SHT-M-4/6
200001855
200 - 230
4 - 6
DPF 2/6-SHT-M-6/8
200001856
6 - 8
DPF 2/6-SHT-M-8/10
200001857
8 - 10
DPF 2/6-SHT-H-4/6
200001858
230 - 260
4 - 6
DPF 2/6-SHT-H-6/8
200001859
6 - 8
DPF 2/6-SHT-H-8/10
200001860
8 - 10
SPECIFICATIONS
ELECTRICAL
MODEL
DPF 2/6-SHT-...
TX/RX FREQUENCY
DPF 2/6-SHT-L: 175 - 200
MHz
DPF 2/6-SHT-M: 200 - 230
MHz
DPF 2/6-SHT-H: 230 - 260
MHz
MAX. INPUT POWER
50 W
INSERTION LOSS TX-ANT AND ANT-RX
(at 4.5 MHz duplex spacing)
Single-channel tuned
Multi-channel tuned, 1.5 MHz BW
≤ 1.2 dB (typ. 1.0 dB)
≤ 1.4 dB (typ. 1.2 dB)
TX NOISE SUPPRESSION ON RX-
FREQUENCY
Single-channel tuned
Multi-channel tuned, 1.5 MHz BW
> 80 dB
> 60 dB
RX ISOLATION ON TX-FREQUENCY
Single-channel tuned
Multi-channel tuned, 1 MHz BW
> 80 dB
> 60 dB
DUPLEX SPACING
4 - 10 MHz (adjustable)
IMPEDANCE
Nom. 50 Ω
SWR
≤ 1.5
MECHANICAL
TEMP. RANGE
–30° C → +60° C
FREQ. STABILITY
Approx. 5 ppm/° C
CONNECTORS
N-female
DIMENSIONS (L x W x H)
191 x 154 x 33 mm
WEIGHT
Approx. 800 g
ORDERING INFORMATION
When ordering, please use the table above to select the appropriate
ordering designation for the desired filter type. If duplex TX and RX
frequencies are stated when ordering, the duplexers are delivered factory
adjusted. If TX and RX frequencies are not stated, the filters are delivered
non-adjusted.
PLEASE NOTE
Special configurations of this filter type may be quoted on request. For
instance, the filter can be delivered with other connector types or with flying
leads (RG 316 coaxial cable) terminated with connectors or for soldering-
connection.
TYPICAL RESPONSE CURVES @ 4.5 MHz DUPLEX SPACING
TYPICAL RESPONSE CURVES @ 9 MHz DUPLEX SPACING