Moog Music MINITAUR User Manual

Page 12

SECTION

MOD(MODUL

TION)

SCILL

ORS

MIXER

LTER

FUNCTION

VALUE/RANGE

CONTROL/

PARAMETER

LFO RATE

Adjusts the LFO frequency

3(MSB)

35(LSB)

0-127

0-63(INT)

64-127(MIDI CLOCK)

See table on

page 24

0-63(OFF)

64-127(ON)

0-63(SAW)

64-127(SQR)

0-63(SAW)

64-127(SQR)

0-63(OFF)

64-127(ON)

0-63(OFF)

64-127(ON)

0-42(LCR)

43-84(LCT)

85-127(EXP)
0-63(Always Glide)

64-127(Glide on

legato notes only)

0-127

(64 is center)

0-127

13(MSB)

45(LSB)

12(MSB)

44(LSB)

17(MSB)

49(LSB)

18(MSB)

50(LSB)

15(MSB)

47(LSB)

16(MSB)

48(LSB)

27(MSB)

59(LSB)

19(MSB)

51(LSB)

21(MSB)

53(LSB)

22(MSB)

50(LSB)

20(MSB)

54(LSB)

5(MSB)

LFO VCO AMOUNT Adjusts the modulation amount

to the VCOs

LFO VCF AMOUNT Adjusts the Modulation amount

to the VCF

LFO MIDI SYNC

(M)

LFO SYNC CLOCK

DIV

(M)

Sets the LFO synchronization

clock divider

Enables or disables ability of LFO

to sync with MIDI CLOCK messages

LFO KEY TRIGGER

(M)

VCO 1 WAVE

Selects the waveform of VCO 1

Selects the waveform of VCO 2

Adjusts the frequency of VCO 2

Adjusts the beat frequency of

VCO 2 (Default is 64)

Enables/disables Note Sync

(Default is off)

Adjusts the Glide (portamento)

rate time

Sets the state of the GLIDE switch

(Glide is enabled when LED is lit)

Selects the type of Glide; Linear

Constant Rate, Linear Constant Time,

or Exponential.
Sets the state of the Legato Glide

parameter when GLIDE is enabled

(Default is OFF)

VCO 2 WAVE

VCO 2 FREQ

VCO 2 BEAT

(M)

GLIDE RATE

NOTE SYNC

(M)

GLIDE SWITCH

GLIDE TYPE

(M)

LEGATO GLIDE

(M)

VCO 1

CUTOFF

Adjusts the Filter Cutoff frequency

RESONANCE

Adjusts the Filter Resonance

parameter

EG AMOUNT

Adjusts the EG amount affecting

the cutoff

FILTER KB TRACK

(M)

Sets the amount of keyboard tracking

for the filter (Default is 32 - about 50%)

FILTER VELOCITY

SENSITIVITY

(M)

Sets the amount of filter velocity

sensitivity (Default is 64 - 50%)

Adjusts the level of VCO 1

VCO 2

Adjusts the level of VC0 2

EXTERNAL IN

LEVEL

(M)

Adjusts the level of the External Audio

Input (Default is 64 = 50% level)

Re-triggers the LFO to the start of

the cycle (Default is OFF)

MIDI CONTROL CHANGE (CC) MESSAGES
The tables on the following pages list all MIDI CC messages for the
Minitaur. Messages shown with an (M) indicate parameters which are
only accessible via MIDI. Bolded values indicate the appropriate range
for 7-bit messages (MSB).

NOTES:

• The Minitaur sends 7-bit MIDI CC messages for all parameters.

It can receive either 7-bit or 14-bit values for the parameters

controlled by knobs, but only 7-bit values for parameters con-

trolled by switches.

• For all parameters, the MSB indicates the ‘regular’ CC number,

and the LSB indicates the high-resolution ‘fine’ control value.

If you are only sending 7-bit MIDI CC messages to the Minitaur,

use the MSB number by itself. Note that when MSB-only

messages are issued, the value range is always 0-127.

A NOTE ABOUT CONTROL PARAMETERS

LOCAL CONTROL OFF (CC# 122):
This parameter allows the front panel controls to send MIDI, but disconnects
the Minitaur sound engine from direct control by the panel. Per the MIDI
spec, only values of ‘0’ and ‘127’ work (0 = OFF, 127 = ON). If you are conn-
ected to a DAW using USB MIDI patched through, you may need this to
avoid feedback artifacts. After changing the state of LOCAL CONTROL
on/off, the Minitaur remembers the last setting after power down.

ALL SOUNDS OFF/ALL NOTES OFF (CC# 120 or 123):
Both of these parameters are MIDI ‘panic’ functions that are used to silence
hung MIDI notes. Controllers or DAWs may send one or the other command
which is why the Minitaur will respond to either.