Velleman Led Strip Special - Manual (Page 10)

switchinG powER suppLy - Din
Use: switchboards, inaccessible places
(ventilated and dust-free).
with 4 screw connections •
protections: •
short circuit -
overload -
auto recovery •
100% full load burn-in test •
high reliability •
switchinG powER suppLy
Use: switchboards, inaccessible places
(ventilated and dust-free).
cooling: by free air convection •
with screw connections •
protections: •
short circuit -
overload -
auto recovery •
100% full load burn-in test •
high reliability •
constant VoLtaGE
Use: suspended ceiling, wet places, etc...
short circuit protection •
overload protection •
over voltage protection (255V) •
thermal protection (80°) •
waterproof protection IP67
•
temperature
1 connection
length
temperature
2 connections
length
order code
LPS00512R 5w 12VDc
6.30 x 1.18
x 25/32 inch
LPS01012C 10w 12VDc
ø2.28
x 15/16 inch
LPS01012R 10w 12VDc
6.30 x 1.18
x 25/32 inch
LPS02012R 20w 12VDc
6.30 x 1.18
x 25/32 inch
LPS04512B 45w 12VDc
10.12 x 1.42
x 29/32 inch
LPS04512R 45w 12VDc
10.12 x 1.42
x 29/32 inch
LPS06012R 60w 12VDc
6.18 x 2.64
x 1.97 inch
LPS08012R 80w 12VDc
9.45 x 2.64
x 1.97 inch
LPS10012R 100w 12VDc
9.45 x 2.64
x 1.97 inch
LPS10024R 100w 24VDc
9.45 x 2.64
x 1.97 inch
LPS15024R 150w 24VDc
8.98 x 4.72
x 2.52 inch
LPS20024R 200w 24VDc
8.98 x 4.72
x 2.52 inch
PSIN02512 max . 25w 12VDc
3.94 x 3.82
x 1.38 inch
PSIN02524 max. 25w 24VDc
3.94 x 3.82
x 1.38 inch
PSIN04012 max. 40w 12VDc
3.94 x 3.82
x 1.46 inch
PSIN04024 max. 40w 24VDc
3.94 x 3.82
x 1.46 inch
PSIN06012 max. 60w 12VDc
3.94 x 3.82
x 1.38 inch
PSIN06024 max. 60w 24VDc
3.94 x 3.82
x 1.38 inch
PSIN10012 max. 100w 12VDc
3.94 x 3.82
x 1.38 inch
PSIN10024 max. 100w 24VDc
3.94 x 3.82
x 1.46 inch
PSIN15012 max. 150w 12VDc
3.94 x 4.33
x 1.97 inch
PSIN15024 max. 150w 24VDc
3.94 x 4.33
x 1.97 inch
PSIN30012 max. 300w 12VDc
3.94 x 4.49
x 1.93 inch
PSIN30024 max. 300w 24VDc
3.94 x 4.49
x 1.93 inch
order code
PSIN03012D max. 30w 12VDc
PSIN03024D max. 30w 24VDc
PSIN06012D max. 60w 12VDc
PSIN06024D max. 60w 24VDc
p o w e r
SupplieS
usinG thE pRopER powER suppLy
the operating voltage of the power supply has to match the indicated supply voltage of the LeD strip (12 of 24V). It is •
important that the output voltage of the power supply does not exceed the indicated voltage of the LeD strip. the used power
supply rating must be higher than the total consumption of all LeD strips. In the summary table at the back you can find the
consumption of each LeD strip per meter. you only need to multiply the used power by the total length of the strip to calculate
the total consumption (without exceeding the maximum distance).
rgB dimmers and controllers are also limited by a maximum current beyond which they can be damaged. so make sure the
•
power you use to feed the LeD strip never exceeds the permitted current of the dimmer or rgB controller.
usinG
an LED stRip
By default, an LeD strip comes
with a 1-wire connection. Under
normal conditions, this is sufficient.
when an LeD strip is used in enclosures,
LeD profiles or in areas with reduced
cooling, it is better to feed the LeD strip
via 2 connectors. the maximum current
in the LeD strip is then cut in half, thus
ensuring lower operating temperature
and a longer life.
power
supply
15ft LED sTRiP
15ft LED sTRiP
power
supply