Velleman VTSS5 User Manual
Page 4
V. 03 – 2
3.
G
Refer to t
•
Fami
•
All m
to th
•
Only
warra
•
Dama
the d
•
Do n
Prote
4.
O
Refer to t
1 pow
2 tem
3 spon
4 iron
5.
I
5.1
P
1. Put
2. Mak
it in
3. Put
Only
gen
Wa
5.2
E
Connect
station is
5.3
T
1. Use
tem
2. Set
to m
cloc
20/06/2012
General Gu
the Velleman®
Indoor
liquids.
Keep th
are clea
Protect
liarise yourself
modifications of t
e device is not c
use the device
anty.
age caused by d
dealer will not ac
ot switch the de
ect the device ag
Overview
the illustrations
er cord
perature contro
nge
stand
Instruction
Warning: this
unattended w
Preparation
the soldering ir
ke sure the spon
the sponge tra
the soldering ti
y change a sold
tly pull out the
rning: Never u
Electrical Con
the power cord
s now ready for
Temperature
the rotary cont
mperature.
the temperatur
melt some solde
ckwise, wait a lit
idelines
® Service and Q
r use only. Kee
Never put objec
is device away
ar at all times.
this device from
with the functio
the device are f
covered by the
for its intended
disregard of cer
ccept responsib
evice on immed
gainst damage
s on page 2 of th
5
oller
6
7
8
s
s tool must be
when switched
ron holder [4] in
nge [3] is comp
y.
p [5] into the s
ering tip when t
soldering tip. C
use the solderi
nnection
[1] to a 230V/
use.
e setting
trol [2] on the f
re controller [2]
er. If it doesn’t m
ttle while and tr
VTSS
4
Quality Warra
p this device aw
cts filled with liq
from dust and e
m shocks and ab
ons of the device
forbidden for saf
warranty.
d purpose. Using
rtain guidelines
bility for any ens
iately after it ha
by leaving it sw
his manual.
bit
heating eleme
antiskid rubbe
handle
e placed on its
d on.
n the correspon
pletely saturated
shaft [6] and at
the soldering iro
heck the screw
ing iron witho
/50Hz power sup
front panel to sw
] between the s
melt fluidly, rota
ry again until it
S5
anty on the last
way from rain, m
quid on top of o
extreme heat. M
buse. Avoid brut
e before actuall
fety reasons. Da
g the device in a
in this manual i
suing defects or
as been exposed
witched off until
ent
er
stand when n
nding hole in the
d with clean wat
ttach it to the so
on has cooled d
fitting regularly
out the solderin
pply. The power
witch the device
second and third
ate the tempera
does.
pages of this m
moisture, splash
or close to the d
Make sure the v
te force when o
y using it.
amage caused b
an unauthorised
is not covered b
r problems.
d to changes in
it has reached
not in use; do n
e casing of the s
ter and let it dr
oldering iron wi
own. Loosen th
y and tighten it
ng tip.
r LED turns ON
e on and set the
d scale, wait a fe
ature controller
©Vellem
manual.
hing and drippin
evice.
entilation openi
operating the de
by user modifica
d way will void t
by the warranty
temperature.
room temperatu
not leave the t
soldering station
ip off before you
th a coupling nu
e coupling nut a
when necessary
and the solderi
e desired
ew moments an
[2] a little furth
man nv
ng
ings
evice.
ations
the
and
ure.
tool
n.
u put
ut.
and
y.
ng
nd try
her