Velleman SOL10UC2 - Manual (Page 4)

25/11/2010
4. Ove
Refer to the
1 charg
2 load i
3 batter
4 Conne
set-u
a s
b b
5. Ins
• Mount th
holes. U
• First con
polarity!
Note: u
• Then co
solar pa
polarity!
• Finally c
sure the
switched
• When co
(not incl
Do
thi
• To disco
and fina
• Note tha
6. Pro
• Over-dis
voltage b
damage
is fully re
• Over-ch
becomes
damage
• Over-loa
of more t
• Load sh
detected
• Reverse
not funct
the regul
7. Use
• There are
o [1] ch
being
erview
e drawings on page
e indicator
ndicator
ry status
ections for solar pan
up
solar panel *
battery *
tallation
he regulator in a coo
se M4x20 screws (n
nnect a rechargeable
!
se multi-core insula
nnect a solar panel
nel is in accordance
!
connect a DC device
e connected load is i
d off. Use the correc
onnecting an AC loa
l.) between battery
not short circuit o
s will lead to irrev
onnect the regulator
lly the battery [b].
at shorter connectio
otection modes
scharge protection
becomes too low. Th
to the battery. Rem
echarged.
harge protection m
s too high. The powe
to the battery until
ad protection mod
than 10A.
ort circuit protect
.
e polarity protectio
tion when reversed
lator.
e
e 3 LEDs on the SO
harge LED: indicates
charged. When the
SOL10UC2
4
2 of this manual.
5
6
7
nel
c DC/AC c
d DC load
e AC load
ol and ventilated, bu
not included) for eas
e battery [b] (not in
ated copper wire of m
[a] (not incl.) to co
e with the specificati
or appliance [d] (n
in accordance with t
ct polarity!
d [e] (not incl.), ins
[b] and load [e].
or reverse polarity
versible damage.
r, first disconnect th
n wires will reduce
s
n mode. This mode
he power to the outp
move the load from t
mode. This mode wil
er from the solar pa
the voltage drops b
de. This mode will be
tion mode. Enabled
on: in order to prev
connecting polarity
L10UC2:
s that the solar pane
LED is blinking, bat
Connections for ba
Connections for D
reset button
convertor*
*
*
ut dry location using
sy mounting.
ncl.) to connections
max. 2.5mm² and s
onnections [4]. Mak
ions of this regulato
not included) to con
the specifications of
stall a suitable DC-t
y of battery, solar
e solar panel [a], th
power losses.
will be enabled whe
put connectors is cu
the connector and w
l be enabled when t
nel input connector
below an acceptable
e enabled when the
when a short circui
vent possible damag
is detected. Correct
el produce power an
ttery is being trickle
©Velleman nv
attery
C load
* not included
g the 4 mounting
[5]. Use the correc
strip ±5mm.
ke sure the connecte
or. Use the correct
nections [6]. Make
f this regulator and
to-AC convertor [c]
r panel or load, as
hen the load [d or e
en the battery
ut off to prevent
wait until the battery
the battery voltage
is cut off to preven
level.
load draws a curren
t in the load is
ge the regulator will
t the polarity to use
nd the battery is
charged.
v
ct
ed
s
e]
y
t
nt
e