Candy GO 1460D-36S User Manual

Page 10

{

“DIGITAL” DISPLAY

The display’s indicator
system allows you to be
constantly informed about
the status of the machine:

1) WASH TEMPERATURE
When a programme is
selected the relevant
indicator will light up to show
the maximum possible wash
temperature.
Selecting a lower
temperature using the
special button will cause the
corresponding indicator to
light up.
Note: The temperature must
be adjusted before
selecting DEGREE OF
SOILING.

2) DOOR LIGHT
Once the START/PAUSE
button has been pressed
the light first flashes then
stops flashing and remains
on until the end of the wash.
2 minutes after the end of
the wash the light goes off
to show that the door can
now be opened.

3) SPIN SPEED
Once the programme has
been selected, the
maximum spin speed
allowed for that programme
appears on the display.
Pressing the spin button will
reduce the speed by 100
rpm each time the button is
pressed. The minimum
speed allowed is 400 rpm, or
it is possible to omit the spin
by pressing the spin button
repeatedly.

4) DELAY START LIGHT
This flashes when delay start
has been set.

5) CYCLE DURATION
When a programme is
selected the display
automatically shows the
cycle duration, which can
vary, depending on the
options selected.
Once the programme has
started you will be kept
informed constantly of the
time remaining to the end of
the wash.

DIGITALNI PRIKAZOVALNIK
Sistem prikazovanja vas
sproti obve‰ãa o vseh
parametrih pranja:

1) TEMPERATURA PRANJA
Ko izberete program, se
osvetli ustrezen indikator za
najvi‰jo dovoljeno
temperaturo za izbrani
program.
S pomoãjo ustrezne tipke
lahko temperaturo pranja
zniÏate –osvetli se ustrezen
indikator.
Opomba: Temperaturo
morate nastavite pred
nastavljanjem stopnje
umazanosti perila!

2) LUâKA ZA ZAPRTA VRATA
Ko pritisnete na tipko
START/PAUSE (Start/pavza),
luãka najprej utripa, nato pa
ostane osvetljena do konca
programa.

2 minuti po koncu programa
luãka ugasne, kar pomeni,
da je moÏno odpreti vrata.

3) HITROST CENTRIFUGIRANJA
KO izberete program, se na
prikazovalniku prikaÏe
najvi‰ja dovoljena hitrost
centrifugiranja za izbrani
program. S pritiskom na tipko
za nastavljanje hitrosti
centrifugiranja lahko to
hitrost zniÏate; ob vsakem
pritisku na tipko se vrednost
zmanj‰a za 100 vrt./min.
NajniÏja moÏna hitrost
centrifugiranja je 400
vrt./min, ãe pa ‰e enkrat
pritisnete na tipko za
nastavljanje hitrosti
centrifugiranja,
centrifugiranje prekliãete.

4) LUâKA ZA ZAMIK VKLOPA
âe je nastavljen ãasovni
zamik vklopa, luãka utripa.

5) TRAJANJE PROGRAMA
Ko izberete program, se na
prikazovalniku prikaÏe
trajanje programa, ki se
spreminja glede na izbrane
opcije.
Ko stroj zaãne izvajati
program, se ãas do konca
programa na prikazovalniku
stalno prilagaja.

PRE-WASH BUTTON

This option is particularly

useful for heavily soiled

loads and can be used only

on some programmes as

shown in the programmes

table.

Detergent for this

programme should be

added to the compartment

of the soap drawer labelled

“1” (Please refer to

Detergent Drawer Section of

manual). We recommend

you use only 20% of the

recommended quantities

shown on the detergent

pack and fabric conditioner

should not be used for this

programme.

SPIN SPEED BUTTON

The spin cycle is very
important to remove as
much water as possible from
the laundry without
damaging the fabrics. You
can adjust the spin speed of
the machine to suit your
needs.
By pressing this button, it is
possible to reduce the
maximum speed, and if you
wish, the spin cycle can be
cancelled.
To reactivate the spin cycle
is enough to press the
button until you reach the
spin speed you would like to
set.
For not damage the fabrics,
it is not possible to increase
the speed over that
automatically suitable
during the selection of the
program.

It is possible to modify the
spin speed in any moment,
also without to pause the
machine.

NOTE:
THE MACHINE IS FITTED
WITH A SPECIAL
ELECTRONIC DEVICE,
WHICH PREVENTS THE
SPIN CYCLE SHOULD THE
LOAD BE UNBALANCED.
THIS REDUCES THE NOISE
AND VIBRATION IN THE
MACHINE AND SO
PROLONGS THE LIFE OF
YOUR MACHINE.

TIPKA ZA PREDPRANJE
Ta opcija je primerna
predvsem za pranje zelo
umazanega perila; na voljo je
le v kombinaciji z doloãenimi
programi, kot je to razvidno iz
tabele programov.
Detergent za predpranje
odmerite v predelek
predalãka za pralna sredstva,
oznaãen z “1” (Upo‰tevajte
navodila, podana v poglavju
Predalãek za pralna
sredstva!).
Priporoãamo, da uporabite le
20% od priporoãene koliãine,
navedene na embalaÏi
pralnega pra‰ka; pri tem
programu ne uporabljajte
mehãalca za perilo.

GUMB ZA NASTAVITEV
HITROSTI
CENTRIFUGIRANJA
Faza centrifugiranja je zelo
pomembna, saj naj bi iz
perila odstranila ãimveã
vlage, ne da bi ga pri tem
po‰kodovala.
Hitrost centrifuge lahko
prilagodite svojim potrebam.
Z nastavitvijo niÏjih vrednosti
lahko zniÏate maksimalno
hitrost centrifuge na minuto.
Centrifugo lahko tudi
izkljuãite. âe Ïelite ponovno
aktivirati fazo centrifugiranja,
preprosto pritisnete na tipko,
dokler ni nastavljena Ïelena
hitrost centrifugiranja.
Da bi prepreãili po‰kodbe
perila, ni mogoãe nastaviti
vi‰je hitrosti centrifugiranja
od najvi‰je predvidene za
posamezne programe.

Hitrost centrifugiranja lahko
nastavite kadarkoli, ne da bi
morali prej preklopiti stroj v
naãin pavze.

OPOMBA:
STROJ JE OPREMLJEN S
POSEBNO ELEKTRONSKO
NAPRAVO, KI PREPREâUJE
CENTRIFUGIRANJE, âE
PERILO V BOBNU NI
URAVNOTEÎENO. S TEM JE
ZMANJ·ANA GLASNOST
DELOVANJA TER
VIBRACIJE, OBENEM PA
TUDI PODALJ·ANA
ÎIVLJENJSKA DOBA
VA·EGA PRALNEGA
STROJA.