STIEBEL ELTRON SBB WP SOL с 12.05.2008 - Manual (Page 14)

ĜÔ ’Z
ŗƃĜéÑƃĜ qT ZH< ŷŷŷĪńŒê¼¼ùé¼ùŒļĒĉĪ›Ēă
HC`C`Z ’ HTV`.HC
&¼ĉ¼ļ|ù êĉÏĒļă|ŒêĒĉ
OPERATION
1. General information _______________________________________ 14
1.1 Safety instructions ______________________________________________ 14
1.2 Other symbols in this documentation ______________________ 15
1.3 Units of measurement _________________________________________ 15
2. Safety ________________________________________________________ 15
2.1 Intended use _____________________________________________________ 15
2.2 Safety instructions ______________________________________________ 15
2.3 Prüfzeichen ______________________________________________________ 15
3. Appliance description _____________________________________ 15
4. Cleaning, care and maintenance _________________________ 16
4.1 Signal anode consumption indicator _______________________ 16
4.2 Scaling ____________________________________________________________ 16
5. Troubleshooting ____________________________________________ 16
INSTALLATION
6. Safety ________________________________________________________ 17
6.1 General safety instructions ___________________________________ 17
6.2 Regulations, standards and instructions ___________________ 17
6.3 Water installation _______________________________________________ 17
7. Appliance description _____________________________________ 17
7.1 Standard delivery _______________________________________________ 17
7.2 Accessories _______________________________________________________ 17
8. Preparations ________________________________________________ 17
8.1 Installation site __________________________________________________ 17
8.2 Transport _________________________________________________________ 18
9. Preparing for installation _________________________________ 18
9.1 Removing / fitting the cylinder casing _____________________ 18
9.2 Checking the signal anode ____________________________________ 18
9.3 Heating installation ____________________________________________ 18
9.4 Fitting the water connection and the safety assembly __ 18
9.5 Fitting the thermometer and DHW sensor _________________ 19
10. Commissioning _____________________________________________ 19
10.1 Appliance handover ____________________________________________ 19
11. Shutting down ______________________________________________ 19
12. Troubleshooting ____________________________________________ 19
12.1 Fault
table ________________________________________________________ 19
13. Maintenance ________________________________________________ 20
13.1 Checking the safety valve _____________________________________ 20
13.2 Draining the appliance ________________________________________ 20
13.3 Replacing the signal anode ___________________________________ 20
13.4 Cleaning and descaling the appliance ______________________ 20
14. Technische Daten ___________________________________________ 20
14.1 Dimensions and connections _________________________________ 20
14.2 Technische Daten _______________________________________________ 24
WARRANTY
ENVIRONMENT AND RECYCLING
HTV`.HC
1. General information
The chapter “Operation” is intended for appliance users and heat-
ing contractors.
The chapter “Installation” is intended for heating contractors.
Note
Read these instructions carefully before using the appli-
ance and retain them for future reference.
Pass on the instructions to a new user if required.
1.1 Safety instructions
1.1.1 Structure of safety instructions
!
KEYWORD Type of risk
Here, possible consequences are listed that may result
from failure to observe the safety instructions.
f Steps to prevent the risk are listed.
1.1.2 Symbols, type of risk
ZźăĒù `źĤ¼ ĒÏ ļêń÷
Injury
Electrocution
Burns
(burns, scalding)
1.1.3 Keywords
:tqHV B¼|ĉêĉÖ
DANGER Failure to observe this information will result in serious
injury or death.
WARNING Failure to observe this information may result in serious
injury or death.
CAUTION Failure to observe this information may result in non-
serious or minor injury.
!