Skil 0755 RA - Manual (Page 8)

8
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) BATTerY Tool Use ANd CAre
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
6) serVICe
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY INSTRUCTIONS FOR CORDLESS
sHrUB/GrAss sHeArs
GeNerAl
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety
• Ensure that children do not play with the tool
• Only use the tool in daylight or with appropriate artificial
lighting
• Do not trim hedges when they are wet
• Keep hands and feet away from the cutting blade,
especially when switching on the tool
• Never operate the tool in the direct vicinity of persons
(especially children) and animals
• The user is responsible for accidents or hazards
occurring to other people or their property
BeFore Use
• Before using the tool for the first time, it is recommended
to receive practical information
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger
• Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a
qualified person; never open the tool yourself
• Before use, thoroughly inspect the cutting area and
remove all foreign objects that could be entangled in the
cutting blades (such as stones, nails, wire fences, metal
plant supports)
dUrING Use
• Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
• Always wear long trousers, long sleeves and sturdy
shoes when operating the tool
• Take a secure stance when working (do not overreach,
especially when using steps or a ladder)
• Hold the power tool by the insulated gripping
surfaces only, because the cutting blades may
contact hidden wiring or its own cord (cutting blades
contacting a “live” wire may make exposed metal parts of
the power tool “live” and could give the operator an
electric shock)
• Keep the (extension) cord away from the cutting
area (during operation the cord may be hidden in shrubs
and can be accidentally cut by the blades)
• Keep all parts of the body away from the cutting
blades, do not remove cut material or hold material
to be cut when blades are moving, and make sure
the switch is off when clearing jammed material (a
moment of inattention while operating the tool may result
in serious personal injury)
• In case of electrical or mechanical malfunction,
immediately switch off the tool or unplug charger from
power source
AFTer Use
• Carry the tool by the handle with the cutting blades
stopped and, when transporting or storing the tool,
always mount the blade cover (proper handling of the
tool will reduce possible personal injury from the cutting
blades)
CHArGING/BATTerIes
• Charge battery only with the charger that is supplied with
the tool
• Do not charge battery in damp or wet environments
• Do not expose tool/charger to rain
• Store tool/charger in locations where temperature will not
exceed 40°C or drop below 0°C
• Do not use charger when damaged; take it to one of the
officially registered SKIL Service Stations for a safety
check