Yamaha RX-V463 User Manual
Page 70
66
En
SET MENU
■ Center speaker equalizer
D)CENTER GEQ
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: –6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
Test tone
TEST
Use this feature to make adjustments for “CENTER GEQ”
while listening to a test tone.
Choices: OFF, ON
• Select “OFF” to stop test tones and output the currently
selected source component.
• Select “ON” to output test tones from the center and
front left speakers.
■ Low-frequency effect level
E)LFE LEVEL
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective when the input
signal contains the LFE channel.
Control range: –20 to 0 dB
Control step: 1 dB
Speaker
SPEAKER
Adjusts the speaker LFE level.
Headphone
HEADPHONE
Adjusts the headphone LFE level.
Depending on the settings of “LFE/BASS OUT” (see page 64),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
■ Dynamic range
F)DYNAMIC RANGE
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
Speaker
SPEAKER
Adjusts the speaker compression.
Headphone
HEADPHONE
Adjusts the headphone compression.
Choices: MIN, STD, MAX
• Select “MIN” (minimum) if you regularly listen at low
volume levels.
• Select “STD” (standard) for general use.
• Select “MAX” (maximum) to preserve the greatest
amount of dynamic range.
■ Audio settings
G)AUDIO SET
Use this feature to adjust the overall audio settings of this
unit.
Mute type
MUTE TYPE
Use this feature to adjust how much the mute function
reduces the output volume (see page 35).
Choices: FULL, –20dB
• Select “FULL” to completely mute all the audio
output.
• Select “–20dB” to reduce the current volume by 20 dB.
Audio delay
A.DELAY
Use this feature to delay the sound output and synchronize
it with the video image. This may be necessary when
using certain LCD monitors or projectors.
Control range: 0 to 160 ms
Control step: 1 ms
Note
1 SOUND MENU
D)CENTER GEQ
TEST
>OFF
ON
. 100Hz ;;;;;;
0dB
300Hz
;;;;;;
0dB
1kHz
;;;;;;
0dB
3kHz
;;;;;;
0dB
10kHz
;;;;;;
0dB
[ ]/[ ]:Up/Down
p
p
p
[
[ ]/[ ]:Adjust
E)LFE LEVEL
. SPEAKER;;;;;;0dB
HEADPHONE
;;;;0dB
[ ]/[ ]:Up/Down
p
p
p
[
[ ]/[ ]:Adjust
1 SOUND MENU
F)DYNAMIC RANGE
. SPEAKER;;;;;;MAX
HEADPHONE
;;;;MAX
[ ]/[ ]:Up/Down
p
p
p
[
[ ]/[ ]:Adjust
1 SOUND MENU
G)AUDIO SET
. MUTE TYPE;;;FULL
A.DELAY
;;;;;;0ms
MAX VOL.
;;;+16dB
INIT.VOL.
;;;;OFF
[ ]/[ ]:Up/Down
p
p
p
[
[ ]/[ ]:Select
1 SOUND MENU
01EN_RX-V463_U.book Page 66 Friday, February 1, 2008 11:43 AM