Yard Machines MTD27P - Manual (Page 15)

14 13
9. To test if the line is advancing properly, push the but-
ton with your thumb while pulling the line with your
fingers. The line should advance freely. (Fig. 30).
10. In the event of the line breaking inside the spool,
repeat the replacement operation.
11. Start the grass trimmer following the instructions in
the “STARTING” section.
MAINTENANCE
1. Regular cleaning and maintenance of your string
trimmer will ensure efficiency and prolong the life of
your machine.
2. After each cutting operation, take apart and clean out
the grass and soil from: the spool and its slot and in
particular the debris shield.
3. During operation, keep the air slots clean and free of
grass.
4. Only use a cloth soaked with hot water and a soft
brush to clean the string trimmer.
5. Do not spray or wet the appliance with water.
6. Do not use detergents or solvents as these could ruin
the trimmer. The parts made of plastic can easily be
damaged by chemical agents.
7. If the line cutting blade no longer cuts or breaks, have
this replaced by contacting an authorized service
center.
MAINTENANCE INSTRUCTIONS
Fig. 30
Before carrying out
any maintenance
operations, cut off the electric power supply by
disconnecting the plug from the extension
cord.
CAUTION:
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120V~, 60Hz, 3.7Amp
No Load Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8,000/min.
Cutting width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12” (300mm)
Line Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ø0.065” (1.65mm)
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.4 Lbs (2.0 Kg)
SPECIFICATION
PARTS LIST
1 6036-230201 PROJECTIVE GUARD 14 6068-202606 UPPER HANDGRIP (R)
2 6228-202701 GUARD ASS'Y 15 6010-202602 WIRE
2-1 6SDABB04-10 SCREW 16 6010-202601 WIRE
2-2 6250-202503 WIRE CUTTING BLADE 17 6022-230001 SWITCH
2-3 6262-202701 GUARD 18 6028-230003 TRIGGER
3 6228-202004A SPOOL CARRIER ASS'Y 19 6068-202605 UPPER HANDGRIP (L)
3-1 6140-B23101 PILOT 20 6038-202605 HOUSING (L)
3-2 6059-202005A SPOOL COVER 21 6021-202602 DETENT
3-3 6194-202001 WIRE-CUTTING 22 6024-202605 SPRING
3-4 6008-202001A SPOOL CARRIER 23 6056-202607 BUTTON
3-5 6059-202004 SPOOL COVER 24 6024-202603 SPRING
4 6038-202606 HOUSING (R) 25
26
6099-202702 MOTOR 120V
5 6SDABB04-18 SCREW 6154-840001 TERMINAL BLOCK
6 6SDABB04-14 SCREW 27 6024-202601 SPRING
7 6017-230101 JACKET 28 6072-202601 MOTOR PLATE
8 6056-202603 SNAP BUTTON 29 6WSB-04 WASHER
9 6114-202602 ADJUSTABLE ROD 30 6SDAE-03-08 SCREW
10 6SHDB-06-52 SCREW 31 6WSB-03 WASHER
11 6WFB-06 WASHER 32 6SDAB-04-10 SCREEW
12 6NBB-06 NUT 33 6270-202003 CUTTER ASS'Y
13 6196-202601 CENTRAL HANDGRIP 34 6024-202604 SPRING
No. Parts No. Description No. Parts No. Description