Product dimensions, Cabinet opening dimensions, Before you start – Whirlpool 3191799 User Manual
Page 2: Product dimensions before you start, Danger warning, Tools needed: parts supplied
This is the safety alert symbol.
This symbol alerts you to hazards that can kill or
hurt you and others. All safety messages will be
preceded by the safety alert symbol and the word “DANGER”
or “WARNING”. These words mean:
Page 1
2 screws
2 door removal pins
Phillips
screwdriver
1/2" dia.
router bit
Product dimensions
Before you start...
30-3/4"
recessed
height
from
underside
of cooktop
to support
slats
28-3/16"
cooktop
recessed width
23-1/8"
recessed
depth
shipping
foot
31-11/16"
overall
height
Important: Observe all governing codes and
ordinances.
Proper installation is your responsibility. Have a qualified
technician install this range.
Range location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
Recessed installation area must provide complete
enclosure around the recessed portion of the range.
Electrical ground is required. See “Electrical requirements.”
IMPORTANT: Some cabinet and building materials are not
designed to withstand the heat produced by the oven for
baking and self-cleaning. Check with your builder or cabinet
supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.
Range support surface MUST be solid, level and flush with
bottom of cabinet cutout.
Do not seal range to side cabinets.
When installing a cooktop under existing cabinets and the
installation does not meet the minimum cabinet clearances.
Install a range hood above the cooktop to avoid burn
hazards.
Copies of the standards listed may be obtained from:
** National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Tools needed:
Parts supplied:
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA
70 — latest edition**, and all local codes and ordinances.
7/8" min.
required
between
cutout and
cabinet door
or hinge.
Locate electrical
supply junction
box on cutout
floor or on rear
wall (shown)
near floor line.
Top of countertop
Note: countertop
must be level
across front and
front to back.
Front view of
cabinet cutout
For minimum
clearances to the
top of cooktop see
Note.*
*Note: 24" min. when bottom of wood or
metal cabinet is protected by not less than
1/4" flame retardant millboard covered
with not less than No. 28 MSG sheet steel,
0.015" stainless steel, 0.024" aluminum or
0.020" copper.
30" min. clearance between the top of the
cooking platform and the bottom of an
unprotected wood or metal cabinet.
wall
1-1/8"
max.
13" max. upper
cabinet depth
19-5/8"
25" countertop
depth
24" lower
cabinet depth
floor
cabinet
front
Side view of
cabinet cutout
30"
overall
width
You can be killed or
seriously injured if you
don’t follow instructions.
DANGER
WARNING
Your safety and the safety of others is very
important.
We have provided many important safety messages in this
manual and on your appliance. Always read and obey all
safety messages.
All safety messages will identify the hazard, tell you how to
reduce the chance of injury, and tell you what can happen if
the instructions are not followed.
You will be killed or
seriously injured if you
don’t follow instructions.
Mobile home installation
The installation of this range must conform to the
Manufactured Home Construction and Safety Standards,
Title 24 CFR, Part 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD, Part
280); or when such standard is not applicable, the Standard
for Manufactured Homes Installations (Manufactured Home
Sites, Communities and Setups), ANSI A225.1/NFPA 501A,
or with local codes.**
When this range is installed in mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.
Four-wire power supply cable must be used in a mobile
home installation. The appliance wiring will need to be
revised. See four-wire electrical connection, Page 3.
1-1/2" max.
countertop
thickness
Top view of
cabinet cutout
28-5/32" oven
recessed width
31-1/2"
overall
cooktop
width
Cabinet opening dimensions
Install a 3-1/2"-wide
support slat on each
side. Slats must be level
front to back and with
each other.
30-3/4"
top of
counter-
top to
bottom
of cabinet
cutout
30-3/4"
top of
countertop to
support slats
21"
cooktop
depth
24-13/32"
to back
of oven
28-1/2" min.
opening width
28-5/8"
opening is
recommended,
if available.
36" overall
countertop
height
1/4"
radius both
corners
Countertop preparation:
Front edges: You may need to
shave or cut the trim of formed
or metal front-edged
countertops to clear the 30"
width of cooktop.
If countertop thickness is
more than 1-1/2" inches
thick: Countertop must be
notched as shown to avoid
damaging the oven control
panel.
If countertop extends more
1-1/8" beyond cabinet front:
Notch countertop as shown
to clear oven control panel.
30-1/8"
notch width
to be equal
both sides
notch width
to be equal
both sides
1-1/2"
max
30-1/8"
1-1/8"
max
cabinet
front
30”