Worksaver HK-102 - Manual

STATEMENT
OF POLICY
It is the policy of Worksaver,
Inc. to improve its products
where it is possible and practical
to do so. Worksaver, Inc.
reserves the right to make
changes or improvements in
design and construction at any
time, without incurring the oblig-
ation to make these changes on
previously manufactured units.
S A F E T Y P R E C A U T I O N S
MOST ACCIDENTS OCCUR BECAUSE OF NEGLECT OR CARELESSNESS.
AVOID NEEDLESS ACCIDENTS BY FOLLOWING ALL OF THE SAFETY PRECAUTIONS LISTED BELOW.
• Machinery should be operated only by those who
are responsible and are authorized to do so.
• Stop the engine, lower all equipment, lock the
brakes, and remove the ignition key before dis-
mounting from the tractor.
• Never stand between tractor and implement while
tractor is being backed to hitch.
• Loose fitting clothing should not be worn, to avoid
catching on various parts.
• Detach implement in area where children normally
do not play.
• When performing adjustments or maintenance on
an implement, first lower it to the ground or block it
securely at a workable height.
• Only a qualified operator should be permitted on
tractor when in operation; no riders allowed.
• Make certain everyone is in the clear before starting
tractor or raising or lowering equipment.
• Operate the tractor and implement only while
seated in the driver’s seat.
• Reduce speed when transporting mounted
implements to avoid bouncing and momentary loss
of steering control.
• A heavy load can cause instability of the tractor.
Use extreme care during road travel. Slow down on
turns and watch out for bumps. Tractor may need
front counter-weights to counter-balance the weight
of the implement.
• Reduce speed on hillsides or curves so there is no
danger of tipping.
• Avoid driving too close to the edge of ditches or
creeks.
• Do not transport implement on public roads without
reflectors and slow moving vehicle emblem in
daylight and with approved warning lights at night
and other periods of poor visibility.
• Due to the width of some implements, use extra
caution on highways, farm roads, and when
approaching gates.
• Always be sure the implement is in the proper
position for transport.
• Keep alert and watch the front as well as the rear
when working with the implement.
OWNER’S
MANUAL
MODEL NO.
HK-102
WHEN ORDERING
REPAIR PARTS, ALWAYS
GIVE THE FOLLOWING
INFORMATION:
1. PART NUMBER
2. PART DESCRIPTION
3. MODEL NUMBER
4. NAME OF ITEM
JANUARY 1999
WS-HK009-OG
WORKSAVER LIMITED WARRANTY
W orksaver warrants its implements, parts and accessories to be free from defects
in materials and workmanship for a period of six (6) months from date of purchase.
Upon written approval,
W orksaver will repair or exchange without charge any part,
which upon examination by W orksaver or its authorized agent, shall disclose to be
defective.
This does not apply to (1) parts that have worn out in normal use, (2) parts broken
because of improper assembly or operation by the customer, (3) parts accidentally
damaged, (4) failure of parts traceable to improper care, (5) parts failing through use
of implement for purposes other than those for which it was designed.
The obligations assumed by W orksaver and the limitations expressed herein are in
lieu of all other warranties expressed or implied.
W O R K S AVER, INC.
P.O. BOX 100 LITCHFIELD, IL 62056-0100 (217) 324-5973
WEB: http:// www.worksaver.com E-MAIL: [email protected]
3 PT. HITCH ADAPTER KIT
For IHC / Farmall Models C, Super C, 200, 230
Safety Instructions Assembly & Mounting
Tractor Preparation Maintenance
Operating Instructions Repair Parts
C A U T I O N
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD
BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE
1. Select an area for assembly that is clean and free
of any debris which might cause persons working
on the assembly to trip.
2. Do not lift heavy parts or assemblies. Use crane,
jack, tackle, fork trucks or other mechanical devices.
3. Preview the assembly instructions in your opera-
tor’s manual before proceeding further.
4. If the assembly instructions call for parts or assem-
blies to be blocked up, use only blocking material
that is in good condition and is capable of handling
the weight of the assembly to be blocked. Also
insure that the blocking material is on a clean, dry
surface.
5. Never put hands, or any part of body, under
blocked up assemblies if at all possible.
6. After completing assembly, thoroughly inspect the
machine to be sure that all nuts, bolts, hydraulic fit-
tings or any other fastened assemblies have been
thoroughly tightened.
7. Before operating the machine, thoroughly read the
operation section of your operator’s manual.
8. Before operating, read the maintenance section of
your operator’s manual to be sure that any parts
requiring lubrication, such as gearboxes, are full, to
avoid any possible damage.
9. Before operating equipment – If you have any
questions regarding the proper assembly or
operation, contact your Worksaver dealer or
representative.
OWNER’S
MANUAL
MODEL NO.
HK-102
CAUTION
For Safe Operation
Read Rules And
Instructions Carefully
SINO LEEINGLES, PIDA AYUDA
A AIGUIEN QUE SI LO LEA
PARA QUE LE TRADUZCA LAS
MEDIDAS DE SEGURIDAD.
MAKE EVERY DAY
A HOLIDAY FROM ACCIDENTS
Please work, drive, play and live each day with care
and concern for your safety and that of your family
and fellow citizens.
3 PT. HITCH ADAPTER KIT
For IHC / Farmall Models C, Super C, 200, 230