Walker MDD - Manual (Page 56)

54
ITEM PART DESCRIPTION NO.
NO. NO. REQ’D
ITEM PART DESCRIPTION NO.
NO. NO. REQ’D
Use only genuine Walker ® replacement parts. Effective Date 03-01-06
HI-DUMP KIT
Hi-Dump Kit
1 7613-1 Door Actuator, 7.0/9.5 2
2 7612-4 Door Actuator Arm/RH 1
3 7612-3 Door Actuator Arm/LH 1
4 7620-6 Cable Guide 2
5 7523-2 Clevis Pin W/Hole (1/4 x 5/8) 2
6 7623-2 Power Dump Cable/9.5 2
7 5552 Ball Joint (1/4-28) 2
8 8402-3 Backup Plate 1
9 7628-1 Channel Angle/RH 1
10 8404-4 Channel Angle/LH 1
11 7146 13mm Ball Stud 2
12 7145 Gas Spring Assembly 1
(Includes Items # 11 & 13)
13 7147 Spring Clip 2
14 5841 Retainer Washer (3/8 x 1-1/4) 4
15 8845 Rubber Bumper (30mm OD x 40mm) 3
5/16-18 Female
16 8404-6 Clevis Pin (1/2 x 1-1/2) 1
17 8402-6 Catcher Pivot Plate 2
18 7620-9 Roller Wheel 2
19 8402-2 Catcher Pivot Arm (Includes Item # 20) 1
20 5830 Grease Fitting 5
21 8404-5 Clevis Pin (1/2 x 1-1/4) 1
22 8402-4 Upper Cylinder Mount Arm 1
23 8402-1 Catcher Frame 1
(Includes Item # 20)
24 7845 Rubber Bumper (1.375 x .63) 2
25 8401-4 Upper Pivot Shaft 1
26 8401-5 Pivot Arm (Includes Item # 27) 1
27 8401-9 Decal, Safety Lockout Arm 1
28 5683 Pivot Bearing 2
29 8401-1 Torsion Spring (1-1/2) 1
30 8401-6 Spring Bushing 1
31 8401-3 Safety Lockout Arm 1
32 8401-2 Safety Lockout Spring 1
33 8400-3 Rear Pivot/LH (Includes Items # 20 & 28) 1
34 5214-8 Ball Joint (7/16-20) Hi Strength 2
35 8400-8 Decal, Hi-Dump 1
36 7047-5 Mount Plate 1
37 8430 Body Chute, Hi-Dump (10") 1
8430-1 Body Chute, Hi-Dump (10.5") 1 *
38 8400-10 Auxiliary Power Terminal Plate 1
(Includes Item # 39)
39 8400-7 Decal, Electrical Jumper Warning 1
40 8400-5 Switch Mount 1
41 8400-9 Decal, Hi-Dump Operation 1
42 8400-4 Switch Cover (Includes Item # 41) 1
43 8400-1 Bumper/Hi-Dump Mount 1
(Includes Item # 35)
44 7854 Plastic Tip/Red 1
45 7383-2 Body Latch Hook 1
46 8400-2 Rear Pivot/RH 1
(Includes Items # 20 & 28)
47 8402-7 Control Lift Rod 2
48 5214-9 Ball Joint (7/16-20LH) Hi Strength 4
49 8403-13 Pump Guard 1
50 7847 Rubber Bumper (1.5 OD x 1.0) 1
Fasteners
F002 10-24 Keps Nut 8
F003 1/4-28 Hex Nut 2
F004 1/4-20 Keps Nut 6
F005 1/4-20 ESNA Nut 1
F009 5/16-18 Whiz Locknut 16
F012 3/8-16 Keps Nut 8
F013 3/8-16 Whiz Locknut 4
F016 1/2-13 Self-Locking Nut 2
F025 10-24 x 3/8 PPHMS 1
F028 10-24 x 3/4 PPHMS 4
F031 1/4-20 x 5/8 Hex Bolt 3
F034 5/16-18 x 3/4 Hex Bolt 7
F035 5/16-18 x 1-1/4 Hex Bolt 2
F037 10-24 x 5/8 PTH Screw 2
F038 3/8-16 x 1 Hex Bolt 3
F039 3/8-16 x 1-1/4 Hex Bolt 4
F040 3/8-16 x 1-1/2 Hex Bolt 4
F048 1/2 SAE Washer 1
F049 5/16 SAE Washer 2
F050 1/4 SAE Washer 3
F052 5/16 External Star Lock Washer 1
F068 1/8 x 1 Cotter Pin 2
F069 3/32 x 1/2 Cotter Pin 2
F085 3/16 Rivet Backup Washer 4
F106 3/8-16 x 5/8 Hex Bolt 2
F134 AN960816L Washer 2
F208 5/16-18 x 2-1/4 Hex Bolt 5
F241 .375 x .875 x .10 Washer 2
F267 1/2 x 1 x 1/16 Washer 4
F287 1/4-28 Keps Nut 1
F385 1/4 x 1-1/4 Roll Pin 3
F395 1/4-20 x 2-1/4 FHA Screw SS 4
F396 10-24 x 1-1/4 Hex Bolt 2
F398 1/4-20 x 2 Hex Bolt 2 *
F399 1/2-13 x 3-1/4 Hex Bolt 2
F405 3/8-16x1-1/2 FHA Screw SS 1
F408 7/16-20 Jam Nut 2
F409 7/16-20 Hex Nut/Left Hand 2
* Item used when tractor is equipped with 10.5" GHS Blower.