Worksaver SDM40-60 - Manual (Page 2)

1 38
TA B L E O F C O N T E N T S
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CHECKLISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY SIGNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . 17
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . 20
OWNER MAINTENANCE & LUBRICATION . . . . . . . . . . . . . 23
TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
STATEMENT
OF POLICY
It is the policy of Worksaver,
Inc. to improve its products
where it is possible and practical
to do so. Worksaver, Inc.
reserves the right to make
changes or improvements in
design and construction at any
time, without incurring the oblig-
ation to make these changes on
previously manufactured units.
T O T H E O W N E R :
Read this manual before using your Standard Duty Rotary Cutter. This manual is provided to give you the
necessary operating and maintenance instructions for keeping your rotary cutter in top operating condition.
Please read this manual thoroughly. Understand what each control is for and how to use it. Observe all safety
signs on the machine and noted throughout the manual for safe operation of implement. Keep this manual handy
for ready reference.
Like all mechanical products, it will require cleaning and upkeep. Lubricate the Cutter as specified.
Use only genuine Worksaver, Inc. service parts. Substitute parts will void the warranty and may not meet stan-
dards required for safe and satisfactory operation. Record the model and serial number of your Cutter here:
Model:________________________________________ Serial Number:_______________________________
RETAIL CUSTOMER’S RESPONSIBILITY
It is the Retail Customer and/or Operator’s responsibility to read the Operator’s Manual, to operate, lubri-
cate, maintain, and store the product in accordance with all instructions and safety procedures. Failure
of the operator to read the Operator’s Manual is a misuse of this equipment.
It is the Retail Customer and/or Operator’s responsibility to inspect the product and to have any part(s)
repaired or replaced when continued operation would cause damage or excessive wear to other parts or
cause a safety hazard.
It is the Retail Customer’s responsibility to deliver the product to the authorized Worksaver Dealer, from
whom he purchased it, for service or replacement of defective parts which are covered by warranty.
Repairs to be submitted for warranty consideration must be made within forty-five (45) days of failure.
It is the Retail Customer’s responsibility for any cost incurred by the Dealer for traveling to or hauling
of the product for the purpose of performing a warranty obligation or inspection.
SINO LEEINGLES, PIDA AYUDA A
AIGUIEN QUE SI LO LEA PARA QUE
LE TRADUZCA LAS MEDIDAS DE
SEGURIDAD. COMER GEARBOX - LF 135.800
PA RTS LIST
(5’ & 6’ CUTTERS)
REF. WORKSAVER COMER NO.
NO. PART NO. PART NO. DESCRIPTION REQ'D.
1 650441 0.131.5000.00 Crown Wheel Z22 M5 1
2 650442 0.135.0301.00 Casing 1
3 650443 0.135.2004.00 Shaft 1
4 650444 0.135.6201.00 Pinion Z15 M5 1
5 650445 0.135.7105.00 Spacer 1
6 650446 0.135.1301.00 Cover 1
7 650447 1.135.7100.00 Protective Washer 1
8 650448 8.0.1.00034 Bearing 6205 1
9 171017 8.0.1.00870 Bearing 6207 1
10 650449 8.0.1.00871 Bearing 6208 2
11 650451 8.2.2.00515 Castle Nut M24 x 2 PR80 B 1
12 650452 8.3.2.00409 Bolt Washer 25 x 44 x 4 1
13 650453 8.4.1.00993 Parallel Key B 10 x 8 x 30 1
14 650454 0.100.7500.00 Shim 35.3 1
15 650456 8.5.2.00030 Snap Ring 80 UNI 7437 1
16 650457 8.5.3.00955 Snap Ring SB 81 1
17 650458 8.5.3.01057 Snap Ring SB 125 1
18 650459 8.6.6.00201 Plug 3 / 8 ” Gas 2
19 650461 8.7.1.00748 Double Lip Seal 40 x 80 x 12 1
20 650462 8.7.3.00028 Oil Seal 35 x 52 x 7 1
21 650463 8.7.6.01058 O-Ring OR-4462 1
22 171007 0.224.7500.00 Shim 51.5 1
23 171014 0.259.7500.00 Shim 48.0 1
24 650464 0.267.7500.00 Shim 79.9 1
25 709059 8.5.1.00680 Snap Ring 40 UNI 7436 1
26 650466 0.124.7135.00 Spacer (China) 1
27 650468 8.4.7.00516 Cotter Pin B5 x 50 1