Wharfedale EVP-X12PM - Manual (Page 3)

EVP-X1 2PM/15PM Panel & Description:
1. Level control: The Level control adjusts the overall volume
of the amplified signal.
2. 5 band EQ: Use this Five-Band Graphic EQ to cut or boost
your signal up to 12dB at designed frequency centers.
This is useful for reducing low frequency rumble or
feedback that often occurs on stage.
3. Parallel Line input and output: These two jacks are
provided to supply a signal input to the EVP-X15PM and to
allow for daisy chaining the signal to possibly another
EVP-X15PM or amplifier combination.
4. Speaker out: The Speaker Out is a post EQ, powered
output designed for speakers with a minimum impedance of
8 ohms speaker. This output should be connected only to
non-powered monitor speakers. The EVP-X15M is the
perfect extension monitor to use in this application.
5. Power switch: use this switch to turn the unit on and off.
6. AC Input connector: The line cord (included) which
provides AC power to the unit. Connect the line cord to
this connector and to a properly grounded AC supply.
Damage to the equipment may occur if an improper line
voltage is used.
NEVER REMOVE OR CUT THE GROUND PIN OF THE
LINE CORD PLUG
7. Fuse: If the fuse should fail, it must be replaced with the
same type and value in order to avoid damage to the
equipment and prevent voiding the warranty.
Product Features of the EVP-XP Series:
• 300W RMS/500W Peak amplifier (EVP-X12P, EVP-X12PM)
• 400W RMS/600W Peak amplifier (EVP-X15P,15PM,215P)
• Thermal, DC fault and short circuit protection
• Hi/Low EQ control in the master section
• 5 Band Graphic EQ (EVP-X12PM/15PM onlyoonly)
• External speaker output connector (EVP-X12PM/15PM only)
• Integral tripod stand adaptor (except monitors)
• Balanced line output
• Integral, preset limiter prevents clipping distortion
• Combined Jack and XLR balanced input connectors
• Power on and system AGC protect LED indicators
EVPX-15PB and EVPX-18PB Active Subwoofers
• Stereo line input and speaker level input available for the
powered subwoofer
• Peak limiter that protects the amplifier and speaker from
clipping.
• 0°, 180°Phase switch
• Built-in 600 watt (peak), 400 watt (continuous) amplifier
• Thermal, DC fault and short circuit protection
• Power on and system AGC protect LED indicators
• Integral, preset limiter prevents clipping and distortion. Line-
level stereo inputs are summed before being sent to the
subwoofer’s internal amplifier. This feature allows the subwoofer
to operate in stereo systems using a single subwoofer
A pair of an integral 150Hz, 24dB/Oct crossovers to send a
high-pass, balanced, line-level, stereo signal to a pair of
powered satellite full-range speakers or an external amplifier for
passive satellite speakers.
• A speaker-level, 1/4” TS phone jack is provided. This input is
useful in applications, such as those employing powered
mixers, in which it is more practical to bring a full-range,
speaker-level signal to the subwoofer amplifier
The EVP-X15/18PB is a 15/18 inch direct-radiating powered
subwoofer. A built-in 600 watt (peak) amplifier accepts stereo or
mono line level inputs via balanced, XLR connectors as well as
single channel speaker level input via a 1/4 inch phone jack.
Integral signal processing includes a stereo crossover and
limiting for the internal amplifier. A pair of XLR out-put
connectors may be used to pass the input signals to another
system or to send a high-pass, line-level stereo signal to a pair
of powered, full-range speakers.
1
2
3
4
5
5
6
7
Page 3
W H A R F E D A L E P R O E V P - X P S E R I E S