Wharfedale EVP-X12PM - Manual (Page 2)

Model Name EVP-X12P EVP-X12PM EVP-X15P EVP-X15PM EVP-X215P EVP-X15PB EVP-X18PB
SYSTEM TYPE 12” 2-way 12” 2 way monitor 15” 2-way 15” 2-way monitor 2x15” 2 way 15” compact sub 18” compact sub
FREQ RESP +/- 3 DB 55 - 20kHz 50Hz -20kHz 45 - 20kHz 50 - 20kHz 40 - 20kHz 45 - 200Hz 40 -200Hz
FINISH MATERIAL Black carpet Black carpet Black carpet Black carpet Black carpet Black carpet Black carpet
TRIPOD STAND BOTTOM Yes No Yes No No No No
TRIPOD STAND TOP No No No No No Yes Yes
INPUTS:
INPUT A Switchable Switchable Switchable Line level input Line level input
balanced mic or balanced mic or balanced mic or
line level input line level input line level input line level input line level input
INPUT B Line level input NA Line level input NA Line level input Line level input Line level input
SPEAKER LEVEL INPUT NA NA NA NA NA 1/4” TS Phone Jack 1/4” TS Phone Jack
INPUT CONNECTORS:
INPUT A Combined Combined Combined Combined Combined Combined Combined
Jack and XLR Jack and XLR Jack and XLR Jack and XLR Jack and XLR Jack and XLR Jack and XLR
INPUT B Combined Jack Combined Jack Combined Jack Combined Jack Combined Jack
XLR & RCA NA XLR & RCA NA XLR&RCA and XLR and XLR
Socket Socket Socket
INPUT SENSITIVITY
MIC 5mV 5mV 5mV 5mV 5mV NA NA
RCA 0.5V 0.5V 0.5V 0.5V 0.5V NA NA
LINE 0.775V 0.775V 0.775V 0.775V 0.775V 0.775V 0.775V
INPUT IMPEDANCE
MIC
470 OHMS 470 OHMS 470 OHMS 470 OHMS 470 OHMS NA NA
LINE INPUT A 47K 47K 47K 47K 47K 10K 10K
LINE INPUT B 10kohms 10kohms 10kohms 10K 10K
LINE OUTPUT TYPE Balanced Male Balanced Male Balanced Male Balanced Male Balanced Male Balanced Male Balanced Male
XLR connector XLR connector XLR connector XLR connector XLR connector XLR connector XLR connector
LINE OUTPUT HIGH PASS FILTER
MAIN EQ HF Shelving 5 band graphic EQ HF Shelving 5 band graphic EQ HF Shelving NA NA
+/-12dB@10KHZ +/-12dB@10KHZ +/-12dB@10KHZ
LF Shelving LF Shelving LF Shelving
+/-12dB @80Hz +/-12dB @ 80HZ +/-12dB @80HZ
ACTIVE CROSSOVER NA NA NA NA NA LPF: 150HZ, 24dB LPF: 150Hz, 24dB
PHASE SWITCH NA NA NA NA NA 0 or 180º 0 or 180º
POWER SECTION
AMPLIFIER POWER:
CONTINUOUS
300W 300W 400W 400W 400W 400W 400W
PEAK 500W 500W 600W 600W 600W 600W 600W
EXTENSION SPEAKER OUTPUT NA 1 NA 1 NA NA NA
PROTECTION TYPE Dynamic/AGC Dynamic/AGC Dynamic/AGC Dynamic/AGC Dynamic/AGC Dynamic/AGC Dynamic/AGC
POWER ON INDICATOR GREEN LED GREEN LED GREEN LED GREEN LED GREEN LEd GREEN LED GREEN LED
SYSTEM DYNAMIC AGC ORANGE LED ORANGE LED ORANGE LED ORANGE LED ORANGE LED ORANGE LED ORANGE LED
ENCLOSURE
DIMENSION MM (HXWXD) 590X430X370 560x424x441 675X460X450 645X445X473.5 1058X502X467 591X460X510 610X522X610
WEIGHT (NET) KG 22.9 22.5kg 29.5 27.4 46.8 35.1 49.2
WEIGHT (GROSS) KG 25.6 25.1kg 33.6 30.5 51.6 38.1 52.3
W H A R F E D A L E P R O E V P - X P S E R I E S
Operating/Use
1.
The EVP-X12P,X15P,X215P feature 2 x combined jack and XLR inputs.The two stereo inputs are mixed down to mono
enabling the connection of stereo output products.
2.
Connect the provided power cable to the IEC mains connector on rear of cabinet.
3
Connect the signal cable (balanced or un balanced, see table and description) from audio mixer or processor securely to
your EVP-XP unit (the internal amplifier should be off, power down mode). Where possible use quality connectors. Only
use screened audio cable for the signal input from the audio mixer or processor. If possible use balanced line signal leads
for optimum quality (see description and table of balanced line operation).
4.
If using XLR CONNECTORS, insert the XLR until locked in. If using a jack plug insert until secure.
5.
Power up audio mixer or processor ensuring connections are made.
6.
Power up EVP-XP internal amplifier with levels on zero. Confirm speakers are operating.
7.
The EVP-XP all feature a balanced Male XLR connector on the line output.
8. The EVP-X12PM,X15PM has one speaker extension output allowing the addition of another speaker.
Page 2