Walker DGHS52 - Manual (Page 42)

40
ITEM PART DESCRIPTION NO.
NO. NO. REQ’D
ITEM PART DESCRIPTION NO.
NO. NO. REQ’D
Use only genuine Walker ® replacement parts. Effective Date 08-01-08
56 INCH COMPLETE CARRIER FRAME ASSEMBLY (P/N 6720)
Spring and Pivot Mount Components
1 5975-3 Cable Tie (50# x 7") 4
2 5744-1 Spring Clip Bracket 1
3 5743-1 Spring Cover 2
4 5743-3 Eyebolt (3/8-16 x 2) 2
5 8667-10 Pivot Mount, LH/Adj. 1
6 5830-3 Grease Fitting (45 Degree) 4
7 8667-20 Pivot Mount, RH/Adj. 1
8 5743-6 Extension Spring (1-1/2 x 7-3/4) 2
(Includes Items # 1, F117 & F166)
Carrier Frame Components
9 8674-11 Lever, Deck Lock, LH 1
10 7406-1 Handle Grip, Red 2
11 5748-10 Rubber Mat (1-1/2 x 6) 2
12 6720-1 56 SD Carrier Frame 1
(Includes Item # 11)
13 5740-2 Deck Pin Bushing (5/8) 4
14 8674-10 Lever, Deck Lock, RH 1
15 5830 Grease Fitting 6
16 5850-5 Handle Grip (1 x 1 x 3-3/4) 1
17 6811-25 Tilt Bar With Grip (30") 1
(Includes Item # 16)
18 7775-5 Lock Pin (5/16) 1
Caster Wheel Components
19 5714-7 Bearing Cap 4
20 5714-5 Bearing, Caster Wheel 2
21 5715-4 Caster Wheel, Pneumatic (8 x 3.00-4) 2
(Includes Items # 6, 19 & 20)
5715-10 Tire, Pneumatic (8 x 3.00-4)
*
5715-9 Tire Tube, Pneumatic (2.80/2.50-4) *
5715-3 Caster Wheel & Tire/No-Flat (8 x 3.00-4) **
5715-11 Tire, Caster Wheel/No-Flat (8 x 3.00-4) **
22 5714-3 Axle Spacer Tube 2
23 5770-1 Caster Wheel Fork 2
24 8768-1 Seal (1-3/4 x 1-1/8) 2
25 8037 Bearing Cone (3/4 ID) 4
26 8769-1 Bearing Cup (1-3/4 x 1-7/16) 4
27 8769-9 Dust Cap, Deck Caster 2
Fasteners
F012 3/8-16 Keps Nut 2
F014 3/8-16 ESNA Nut 2
F047 3/8-16 x 4-1/2 Hex Bolt 2
F055 5/8 SAE Washer 2
F068 1/8 x 1 Cotter Pin 2
F098 5/8-18 Slotted Hex Nut 2
F117 Retainer Ring 2
F123 1" External Snap Ring 4
F166 Retainer Ring 2
F317 3/16 x 1 Split Spring Pin 4
F335 3/8-16 x 7/8 Set Screw, SS 2
F336 3/8-16 Jam Nut 2
* Service Part Only
** May be ordered as a factory-installed option or as a kit for
dealer installation. Contact your Walker Dealer.
NOTE: When installing Item # 8 on decks prior to S/N DX-62875,
the swivel hook end should be attached to the deck carrier
frame.