Whirlpool GFG471LVS - Manual (Page 7)

7
4. Replace the burner cap, making sure the alignment pins are
properly aligned with the burner cap.
5. Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
OVEN USE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled. IMPORTANT: The health of some birds is extremely sensitive to the
fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room.
Electronic Oven Controls
Control Display
The display will flash when powered up or after a power loss. Press
CANCEL/OFF to clear. When oven is not in use, the time of day is
displayed. Indicator lights show functions that are in use.
Tones
Tones are audible signals, indicating the following:
One tone
■ Valid pad press
■ Oven is preheated (long tone)
■ Function has been entered
■ Reminder (on some models), repeating each minute after the
end-of-cycle tones
Three tones
■ Invalid pad press
Four tones
■ End of cycle
To Change Tone Settings:
Tone Pitch
Sets the pitch of the tone to either high or low.
Press and hold BROIL for 5 seconds. “TONE PITCH HIGH” or
“TONE PITCH LOW” will appear in the display. Press and hold
BROIL again to change setting.
To exit, press CANCEL/OFF.
Key Press Tones
Activates or turns off the tones when a keypad is pressed.
Press and hold KEEP WARM for 5 seconds. “KEY PRESS TONES
ON” or “KEY PRESS TONES OFF” will appear in the display. Press
and hold KEEP WARM again to change setting.
To exit, press CANCEL/OFF.
End of Cycle Tone
Activates or turns off the tones that sound at the end of a cycle.
Press and hold CONVECT for 5 seconds. “CYCLE END TONE ON”
or “CYCLE END TONE OFF” will appear in the display. Press and
hold CONVECT again to change setting.
To exit, press CANCEL/OFF.
Reminder Tones Disable
Turns off the short tones that sound 1 minute after the end of cycle
tones.
Press and hold BAKE for 5 seconds. “REMINDER TONES ON” or
“REMINDER TONES OFF” will appear in the display. Press and
hold BAKE again to change setting.
To exit, press CANCEL/OFF.
Audible Tones Disable
Turns off all tones, including the end of cycle tone and key press
tones. Reminder tones are still active when all tones are disabled.
Press and hold CLOCK for 5 seconds. “ALL SOUNDS ON” or “ALL
SOUNDS OFF” will appear in the display. Press and hold CLOCK
again to change setting.
To exit, press CANCEL/OFF.
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
To change: Press and hold PRECISE CLEAN for 5 seconds. A tone
will sound, and “°C” or “°F” will appear on the display. Repeat to
change back.
To exit, press CANCEL/OFF.
12-Hour Shutoff
The oven control is set to automatically shut off the oven 12 hours
after the oven initiates a cook or clean function. This will not
interfere with any timed or delay cook functions.
Press and hold START TIME for 5 seconds to toggle to the 12-hour
shutoff function. Scrolling text will display “12 HR SHUT-OFF ON”
or “12 HR SHUT-OFF OFF.” Press and hold to change setting.
To exit, press CANCEL/OFF.
Oven Temperature Control
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door may cause element
cycling to give incorrect readings.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
To Adjust Oven Temperature Calibration:
1. Press and hold OVEN LIGHT for 5 seconds until the oven
display shows the current calibration, for example “0°F.
2. Press the SET TEMP/TIME “+” or “-” arrow pads to increase or
to decrease the temperature in 5°F (3°C) amounts. The
adjustment can be set between 30°F (18°C) and -30°F (-18°C).
3. Press START.
A. Incorrect
B. Correct
A
B